- 您现在的位置：买卖IC网 > PDF目录44717 > LP3906SQXVPFP (NATIONAL SEMICONDUCTOR CORP) 2 A DUAL SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, QCC24 PDF资料下载
参数资料
| 型号： | LP3906SQXVPFP |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 2 A DUAL SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, QCC24 |
| 封装： | 5 X 4 MM, 0.80 MM HEIGHT, LLP-24 |
| 文件页数： | 27/40页 |
| 文件大小： | 4197K |
| 代理商： | LP3906SQXVPFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
For both input and output capacitors, careful interpretation of
the capacitor specification is required to ensure correct device
operation. The capacitor value can change greatly, depend-
ing on the operating conditions and capacitor type.
In particular, the output capacitor selection should take ac-
count of all the capacitor parameters, to ensure that the
specification is met within the application. The capacitance
can vary with DC bias conditions as well as temperature and
frequency of operation. Capacitor values will also show some
decrease over time due to aging. The capacitor parameters
are also dependent on the particular case size, with smaller
sizes giving poorer performance figures in general. As an ex-
ample, the graph below shows a typical graph comparing
different capacitor case sizes in a Capacitance vs. DC Bias
plot.
20197828
Graph Showing a Typical Variation in Capacitance vs. DC
Bias
As shown in the graph, increasing the DC Bias condition can
result in the capacitance value that falls below the minimum
value given in the recommended capacitor specifications ta-
ble. Note that the graph shows the capacitance out of spec
for the 0402 case size capacitor at higher bias voltages. It is
therefore recommended that the capacitor manufacturers'
specifications for the nominal value capacitor are consulted
for all conditions, as some capacitor sizes (e.g. 0402) may not
be suitable in the actual application.
The ceramic capacitor’s capacitance can vary with tempera-
ture. The capacitor type X7R, which operates over a temper-
ature range of 55°C to +125°C, will only vary the capacitance
to within ±15%. The capacitor type X5R has a similar toler-
ance over a reduced temperature range of 55°C to +85°C.
Many large value ceramic capacitors, larger than 1 F are
manufactured with Z5U or Y5V temperature characteristics.
Their capacitance can drop by more than 50% as the tem-
perature varies from 25°C to 85°C. Therefore X7R is recom-
mended over Z5U and Y5V in applications where the ambient
temperature will change significantly above or below 25°C.
Tantalum capacitors are less desirable than ceramic for use
as output capacitors because they are more expensive when
comparing equivalent capacitance and voltage ratings in the
0.47 F to 4.7 F range.
Another important consideration is that tantalum capacitors
have higher ESR values than equivalent size ceramics. This
means that while it may be possible to find a tantalum capac-
itor with an ESR value within the stable range, it would have
to be larger in capacitance (which means bigger and more
costly) than a ceramic capacitor with the same ESR value. It
should also be noted that the ESR of a typical tantalum will
increase about 2:1 as the temperature goes from 25°C down
to 40°C, so some guard band must be allowed.
Input Capacitor Selection for SW1 and SW2
A ceramic input capacitor of 10 F, 6.3V is sufficient for the
magnetic dc/dc converters. Place the input capacitor as close
as possible to the input of the device. A large value may be
used for improved input voltage filtering. The recommended
capacitor types are X7R or X5R. Y5V type capacitors should
not be used. DC bias characteristics of ceramic capacitors
must be considered when selecting case sizes like 0805 and
0603. The input filter capacitor supplies current to the PFET
switch of the dc/dc converter in the first half of each cycle and
reduces voltage ripple imposed on the input power source. A
ceramic capacitor’s low ESR (Equivalent Series Resistance)
provides the best noise filtering of the input voltage spikes due
to fast current transients. A capacitor with sufficient ripple
current rating should be selected. The Input current ripple can
be calculated as:
The worse case is when V
IN = 2VOUT
Output Capacitor Selection for SW1, SW2
A 10 F, 6.3V ceramic capacitor should be used on the output
of the sw1 and sw2 magnetic dc/dc converters. The output
capacitor needs to be mounted as close as possible to the
output of the device. A large value may be used for improved
input voltage filtering. The recommended capacitor types are
X7R or X5R. Y5V type capacitors should not be used. DC bias
characteristics of ceramic capacitors must be considered
when selecting case sizes like 0805 and 0603. DC bias char-
acteristics vary from manufacturer to manufacturer and DC
bias curves should be requested from them and analyzed as
part of the capacitor selection process.
The output filter capacitor of the magnetic dc/dc converter
smoothes out current flow from the inductor to the load, helps
maintain a steady output voltage during transient load
changes and reduces output voltage ripple. These capacitors
must be selected with sufficient capacitance and sufficiently
low ESD to perform these functions.
The output voltage ripple is caused by the charging and dis-
charging of the output capacitor and also due to its ESR and
can be calculated as follows:
Voltage peak-to-peak ripple due to ESR can be expressed as
follows:
V
PP–ESR = 2 × IRIPPLE × RESR
Because the V
PP-C and VPP-ESR are out of phase, the rms val-
ue can be used to get an approximate value of the peak-to-
peak ripple:
33
www.national.com
LP3906
相关PDF资料 |
PDF描述 |
|---|---|
| LP3906SQXPPXP | 2 A DUAL SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, QCC24 |
| LP3907SQ-JIXI | 1.5 A DUAL SWITCHING CONTROLLER, 2100 kHz SWITCHING FREQ-MAX, QCC24 |
| LP3918TL-I | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PBGA25 |
| LP3923TLX | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PBGA30 |
| LP3923TLX-VB | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PBGA30 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LP3906SQX-VPFP/NOPB | 功能描述:其他电源管理 RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel |
| LP3907 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual High-Current Step-Down DC/DC and Dual Linear Regulator with I2C Compatible Interface |
| LP3907QSQ-JJXP/NOPB | 功能描述:上下转换器 Dual Hi-Current SD DC/DC RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| LP3907QSQ-JXI7/NOPB | 功能描述:低压差稳压器 - LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| LP3907QSQ-JXIP/NOPB | 功能描述:上下转换器 Dual Hi-Current SD DC/DC RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
发布紧急采购，3分钟左右您将得到回复。