- 您现在的位置：买卖IC网 > PDF目录80331 > LSM2-T/6-W3NG-C 1-OUTPUT 19.8 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | LSM2-T/6-W3NG-C |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 19.8 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT |
| 文件页数： | 7/17页 |
| 文件大小： | 1394K |
| 代理商： | LSM2-T/6-W3NG-C |
LSM2 Series
Single Output, Non-isolated, Selectable-Output POL DC/DC Converters
MDC_LSM2_A01 Page 5 of 7
P O W E R E L E C T R O N I C S D I V I S I O N
D C / D C C O N V E R T E R S
www.cd4power.com
Power Good Output
The Power Good Output consists of an unterminated BSS38 small signal
field effect transistor and a dual window comparator input circuit driving the
gate of the FET. Power Good is TRUE (open drain, high impedance state) if the
converter’s power output voltage is within about ±0% of the setpoint. Thus,
the PG TRUE condition indicates that the converter is approximately within
regulation. Since an overcurrent condition occurs at about 2% output voltage
reduction, the Power Good does not directly measure an output overcurrent
condition at rated maximum output current. However, gross overcurrent or
an output short circuit will set Power Good to FALSE (+0.2V saturation, low
impedance condition).
Using a simple connection to external logic (and returned to the converter’s
Common connection), the Power Good output is unterminated so that the user
may adapt the output to a variety of logic families. The PG pin may therefore
be used with logic voltages which are not necessarily the same as the input
or output power voltages. Install an external pullup resistor to the logic supply
voltage which is compatible with your logic system. When the Power Good is
out of limit, the FET is at saturation, approximately +0.2V output. Keep this
LOW (FALSE) pulldown current to less than 0mA.
Please note that Power Good is briefly false during Sequence ramp-up. Ignore
Power Good while in transition.
Figure 18. Equivalent Power Good Circuit
www.cd4power.com
[5] Be aware of the input characteristics of the Sequence pin. The high
input impedance affects the time constant of any small external ramp
capacitor. And the bias current will slowly charge up any external caps
over time if they are not grounded. The internal pull-up resistor to +VIN is
typically 400k
W to MW.
Notice in the simplified Sequence/Track equivalent circuit (Figure 7) that
a blocking diode effectively disconnects this circuit when the Sequence/
Track pin is pulled up to +VIN or left open.
[6] Allow the converter to eventually achieve its full-rated setpoint output
voltage. Do not remain in ramp up/down mode indefinitely. The converter
is characterized and meets all its specifications only at the setpoint
voltage (plus or minus any trim voltage). During the ramp-up phase, the
converter is not considered fully in regulation. This may affect perfor-
mance with excessive high current loads at turn-on.
[7] The Sequence is a sensitive input into the feedback control loop of the
converter. Avoid noise and long leads on this input. Keep all wiring very
short. Use shielding if necessary. Consider adding a small parallel ce-
ramic capacitor across the Sequence/Track input (see Figure 6) to block
any external high frequency noise.
[8] If one converter is slaving to another master converter, there will be a
very short phase lag between the two converters. This can usually be
ignored.
[9] You may connect two or more Sequence inputs in parallel from two
converters. Be aware of the increasing pull-up bias current and reduced
input impedance.
[0] Any external capacitance added to the converter’s output may affect
ramp up/down times and ramp tracking accuracy.
相关PDF资料 |
PDF描述 |
|---|---|
| LV5122T | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LTC3851IUD-1#PBF | 0.05 A SWITCHING CONTROLLER, 530 kHz SWITCHING FREQ-MAX, PQCC16 |
| LTC6992IDCB-1#TRPBF | 0.02 A SWITCHING CONTROLLER, PDSO6 |
| LTC6992IDCB-2#TRMPBF | 0.02 A SWITCHING CONTROLLER, PDSO6 |
| LM2575-5.0WUTR | 3.2 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PSSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LSM2U | 功能描述:限位开关 LIMIT SWITCH RoHS:否 制造商:Honeywell 触点形式:SPDT 执行器:Non-Contact 电流额定值:30 mA 电压额定值 AC: 电压额定值 DC:3.6 V 工作力:10 g IP 等级:IP 67 NEMA 额定值:1, 4, 12, 13 端接类型:4-Pin M12 Connector 安装:SMD/SMT |
| LSM-3.3/10-D12 | 功能描述:DC/DC转换器 33W 12V to 3.3V 10A SMT Package RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| LSM-3.3/10-D12-C | 功能描述:DC/DC转换器 33W 12V to 3.3V 10A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| LSM-3.3/10-D12EB | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:10 Amp DC/DC Power Converter Evaluation Boards |
| LSM-3.3/10-D5 | 功能描述:DC/DC转换器 33W 5V to 3.3V 10A SMT Package RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。