- 您现在的位置：买卖IC网 > PDF目录14798 > LT1054IS8#PBF (Linear Technology)IC REG SWITCHD CAP DBL INV 8SOIC PDF资料下载
参数资料
| 型号： | LT1054IS8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 5/16页 |
| 文件大小： | 0K |
| 描述： | IC REG SWITCHD CAP DBL INV 8SOIC |
| 标准包装： | 100 |
| 类型： | 切换式电容器（充电泵），倍增器，反相 |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调 |
| 输入电压： | 3.5 V ~ 15 V |
| 频率 - 开关： | 25kHz |
| 电流 - 输出： | 100mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 8-SOIC |
| 产品目录页面： | 1339 (CN2011-ZH PDF) |
LT1054/LT1054L
TYPICAL PERFORMANCE CHARACTERISTICS
Regulated Output Voltage
Reference Voltage Temperature
Coefficient
–4.7
–4.8
– 4.9
–5.0
–5.1
–11.6
–11.8
–12.0
–12.2
–12.4
100
80
60
40
20
0
–20
–40
–60
–80
V REF AT 0 = 2.500V
–12.6
–50 –25
0
25
50
75
100
125
–100
–50 –25
0
25
50
75
100
125
TEMPERATURE (°C)
LT1054 ? TPC09
PIN FUNCTIONS
FB/SHDN (Pin 1): Feedback/Shutdown Pin. This pin has
two functions. Pulling Pin 1 below the shutdown threshold
(≈ 0.45V) puts the device into shutdown. In shutdown the
reference/regulator is turned off and switching stops. The
switches are set such that both C IN and C OUT are discharged
through the output load. Quiescent current in shutdown
drops to approximately 100μA (see Typical Performance
Characteristics). Any open-collector gate can be used to
put the LT1054 into shutdown. For normal (unregulated)
operation the device will start back up when the external
gate is shut off. In LT1054 circuits that use the regulation
feature, the external resistor divider can provide enough
pull-down to keep the device in shutdown until the output
capacitor (C OUT ) has fully discharged. For most applica-
tions where the LT1054 would be run intermittently, this
does not present a problem because the discharge time
of the output capacitor will be short compared to the off-
time of the device. In applications where the device has
to start up before the output capacitor (C OUT ) has fully
discharged, a restart pulse must be applied to Pin 1 of
the LT1054. Using the circuit of Figure 5, the restart signal
can be either a pulse (t p > 100μs) or a logic high. Diode
coupling the restart signal into Pin 1 will allow the output
voltage to come up and regulate without overshoot. The
resistor divider R3/R4 in Figure 5 should be chosen to
provide a signal level at pin 1 of 0.7V to 1.1V.
TEMPERATURE (°C)
LT1054 ? TPC10
Pin 1 is also the inverting input of the LT1054’s error
amplifier and as such can be used to obtain a regulated
output voltage.
CAP + /CAP – (Pin 2/Pin 4): Pin 2, the positive side of the
input capacitor (C IN ), is alternately driven between V +
and ground. When driven to V + , Pin 2 sources current
from V + . When driven to ground Pin 2 sinks current to
ground. Pin 4, the negative side of the input capacitor, is
driven alternately between ground and V OUT . When driven
to ground, Pin 4 sinks current to ground. When driven to
V OUT Pin 4 sources current from C OUT . In all cases current
flow in the switches is unidirectional as should be expected
using bipolar switches.
V OUT (Pin 5): In addition to being the output pin this pin
is also tied to the substrate of the device. Special care
must be taken in LT1054 circuits to avoid pulling this
pin positive with respect to any of the other pins. Pulling
Pin?5 positive with respect to Pin 3 (GND) will forward
bias the substrate diode which will prevent the device from
starting. This condition can occur when the output load
driven by the LT1054 is referred to its positive supply (or
to some other positive voltage). Note that most op amps
present just such a load since their supply currents flow
from their V + terminals to their V – terminals. To prevent
start-up problems with this type of load an external
1954lfg
5
相关PDF资料 |
PDF描述 |
|---|---|
| LT1766IGN#PBF | IC REG BUCK ADJ 1.5A 16SSOP |
| ESC20DREN-S13 | CONN EDGECARD 40POS .100 EXTEND |
| LT3508HFE#PBF | IC REG BUCK ADJ 1.4A DL 16TSSOP |
| LT1071CT#PBF | IC REG MULTI CONFIG ADJ TO220-5 |
| LT1171CT#PBF | IC REG MULTI CONFIG ADJ TO220-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1054ISW | 功能描述:IC REG MULTI CONFIG ADJ 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1054ISW#PBF | 功能描述:IC REG MULTI CONFIG ADJ 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
| LT1054ISW#TR | 功能描述:IC REG MULTI CONFIG ADJ 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1054ISW#TRPBF | 功能描述:IC REG MULTI CONFIG ADJ 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1054LCS8 | 功能描述:IC REG MULTI CONFIG ADJ 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。