- 您现在的位置：买卖IC网 > PDF目录14046 > LT1073CN8-12 (Linear Technology)IC REG BUCK BST INV 12V .4A 8DIP PDF资料下载
参数资料
| 型号： | LT1073CN8-12 |
| 厂商： | Linear Technology |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BST INV 12V .4A 8DIP |
| 标准包装： | 50 |
| 类型： | 降压（降压），升压（升压），反相 |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 12V |
| 输入电压： | 1 V ~ 30 V |
| 频率 - 开关： | 19kHz |
| 电流 - 输出： | 400mA |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 包装： | 管件 |
| 供应商设备封装： | 8-PDIP |
LT1073
APPLICATIO S I FOR ATIO
In Figure 9, the input is negative while the output is
positive. In this configuration, the magnitude of the input
voltage can be higher or lower than the output voltage. A
V OUT + V DIODE
V IN – V SW
<
1
1 – DC
reduces the comparator hysteresis by the gain of the gain
levelshift,providedbythePNPtransistor,suppliesproper
polarity feedback information to the regulator.
Using the I LIM Pin
The LT1073 switch can be programmed to turn off at a set
switch current, a feature not found on competing devices.
This enables the input to vary over a wide range without
exceeding the maximum switch rating or saturating the
inductor. Consider the case where analysis shows the
LT1073 must operate at an 800mA peak switch current
with a 2V input. If V IN rises to 4V, the peak switch current
will rise to 1.6A, exceeding the maximum switch current
rating. With the proper resistor (see the “Maximum Switch
Current vs R LIM ” characteristic) selected, the switch cur-
rent will be limited to 800mA, even if the input voltage
increases. The LT1073 does this by sampling a small
fraction of the switch current and passing this current
through the external resistor. When the voltage on the I LIM
pin drops a V BE below V IN , the oscillator terminates the
cycle. Propagation delay through this loop is about 2 μ s.
Another situation where the I LIM feature is useful is when
the device goes into continuous mode operation. This
occurs in step-up mode when
I L
When the input and output voltages satisfy this relation-
ship, inductor current does not go to zero during the
switch OFF time. When the switch turns on again, the
current ramp starts from the nonzero current level in the
inductor just prior to switch turn-on. As shown in
Figure 10, the inductor current increases to a high level
before the comparator turns off the oscillator. This high
current can cause excessive output ripple and requires
oversizing the output capacitor and inductor. With the I LIM
feature, however, the switch current turns off at a pro-
grammed level as shown in Figure 11, keeping output
ripple to a minimum.
Using the Gain Block
The gain block (GB) on the LT1073 can be used as an error
amplifier, low-battery detector or linear post-regulator.
The gain block itself is a very simple PNP input op amp with
an open-collector NPN output. The (–) input of the gain
block is tied internally to the 212mV reference. The (+)
input comes out on the SET pin.
Arrangement of the gain block as a low battery detector is
straightforward. Figure 12 shows hookup. R1 and R2 need
only be low enough in value so that the bias current of the
SET input does not cause large errors. 100k ? for R2 is
adequate.
Output ripple of the LT1073, normally 150mV at 5V OUT ,
by LIMIT PROGRAMMED
can be reduced significantly CURRENT placing the gain block in
front of the FB input as shown in Figure 13. This effectively
I L
block. Output ripple can be reduced to just a few millivolts
using this technique. Ripple reduction works with step-
SWITCH
ON
OFF
1073 F10
SWITCH
ON
OFF
1073 F11
down or inverting modes as well.
10
Figure 10. No Current Limit Causes
Large Inductor Current Build-Up
Figure 11. Current Limit Keeps Inductor Current Under Control
相关PDF资料 |
PDF描述 |
|---|---|
| V24B15C150B | CONVERTER MOD DC/DC 15V 150W |
| LT1073CN8 | IC REG BUCK BST INV ADJ .4A 8DIP |
| GBA40DTKS | CONN EDGECARD 80POS DIP .125 SLD |
| LT1073CN8-5 | IC REG BUCK BST INV 5V 0.4A 8DIP |
| LT1110CN8-5 | IC REG BUCK BOOST 5V 0.4A 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1073CN8-12#PBF | 功能描述:IC REG BUCK BST INV 12V .4A 8DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1073CN8-5 | 功能描述:IC REG BUCK BST INV 5V 0.4A 8DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1073CN85#PBF | 制造商:Linear Technology 功能描述:LT1073CN85#PBF |
| LT1073CN8-5#PBF | 功能描述:IC REG BUCK BST INV 5V 0.4A 8DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1073CN85PBF | 制造商:Linear Technology 功能描述:LT1073CN85PBF |
发布紧急采购，3分钟左右您将得到回复。