- 您现在的位置：买卖IC网 > PDF目录14046 > LT1073CN8-12 (Linear Technology)IC REG BUCK BST INV 12V .4A 8DIP PDF资料下载
参数资料
| 型号： | LT1073CN8-12 |
| 厂商： | Linear Technology |
| 文件页数： | 5/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BST INV 12V .4A 8DIP |
| 标准包装： | 50 |
| 类型： | 降压（降压），升压（升压），反相 |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 12V |
| 输入电压： | 1 V ~ 30 V |
| 频率 - 开关： | 19kHz |
| 电流 - 输出： | 400mA |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 包装： | 管件 |
| 供应商设备封装： | 8-PDIP |
LT1073
OPERATIO
LT1073
The LT1073 is gated oscillator switcher. This type archi-
tecture has very low supply current because the switch is
cycled only when the feedback pin voltage drops below the
reference voltage. Circuit operation can best be under-
stood by referring to the LT1073 Block Diagram. Com-
parator A1 compares the FB pin voltage with the 212mV
reference signal. When FB drops below 212mV, A1 switches
on the 19kHz oscillator. The driver amplifier boosts the
signal level to drive the output NPN power switch Q1. An
adaptive base drive circuit senses switch current and
provides just enough base drive to ensure switch satura-
tion without overdriving the switch, resulting in higher
efficiency. The switch cycling action raises the output
voltage and FB pin voltage. When the FB voltage is suffi-
A resistor connected between the I LIM pin and V IN adjusts
maximum switch current. When the switch current ex-
ceeds the set value, the switch is turned off. This feature
is especially useful when small inductance values are used
with high input voltages. If the internal current limit of 1.5A
is desired, I LIM should be tied directly to V IN . Propagation
delay through the current-limit circuitry is about 2 μ s.
In step-up mode, SW2 is connected to ground and SW1
drives the inductor. In step-down mode, SW1 is con-
nected to V IN and SW2 drives the inductor. Output voltage
is set by the following equation in either step-up or step-
down modes where R1 is connected from FB to GND and
R2 is connected from V OUT to FB.
(
)
V OUT = 212 mV ?
+ 1 ?
cienttotripA1,theoscillatorisgatedoff.Asmallamount
of hysteresis built into A1 ensures loop stability without
external frequency compensation. When the comparator
? R2
? R 1
?
?
is low the oscillator and all high current circuitry is turned
off, lowering device quiescent current to just 95 μ A for the
reference, A1 and A2.
The oscillator is set internally for 38 μ s ON time and 15 μ s
OFF time, optimizing the device for step-up circuits where
V OUT ≈ 3V IN , e.g., 1.5V to 5V. Other step-up ratios as well
as step-down (buck) converters are possible at slight
losses in maximum achievable power output.
A2 is a versatile gain block that can serve as a low-battery
detector, a linear post-regulator, or drive an undervoltage
lockout circuit. The negative input of A2 is internally
connected to the 212mV reference. An external resistor
divider from V IN to GND provides the trip point for A2. The
AO output can sink 100 μ A (use a 56k resistor pull-up to
5V). This line can signal a microcontroller that the battery
voltage has dropped below the preset level.
LT1073-5 and LT1073-12
The LT1073-5 and LT1073-12 fixed output voltage ver-
sions have the gain-setting resistor on-chip. Only three
external components are required to construct a fixed-
output converter. 5 μ A flows through R1 and R2 in the
LT1073-5, and 12.3 μ A flows in the LT1073-12. This
current represents a load and the converter must cycle
from time to time to maintain the proper output voltage.
Output ripple, inherently present in gated-oscillator de-
signs, will typically run around 150mV for the LT1073-5
and 350mV for the LT1073-12 with the proper inductor/
capacitor selection. This output ripple can be reduced
considerably by using the gain block amp as a preamplifier
in front of the FB pin. See the Applications Information
section for details.
5
相关PDF资料 |
PDF描述 |
|---|---|
| V24B15C150B | CONVERTER MOD DC/DC 15V 150W |
| LT1073CN8 | IC REG BUCK BST INV ADJ .4A 8DIP |
| GBA40DTKS | CONN EDGECARD 80POS DIP .125 SLD |
| LT1073CN8-5 | IC REG BUCK BST INV 5V 0.4A 8DIP |
| LT1110CN8-5 | IC REG BUCK BOOST 5V 0.4A 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1073CN8-12#PBF | 功能描述:IC REG BUCK BST INV 12V .4A 8DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1073CN8-5 | 功能描述:IC REG BUCK BST INV 5V 0.4A 8DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1073CN85#PBF | 制造商:Linear Technology 功能描述:LT1073CN85#PBF |
| LT1073CN8-5#PBF | 功能描述:IC REG BUCK BST INV 5V 0.4A 8DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1073CN85PBF | 制造商:Linear Technology 功能描述:LT1073CN85PBF |
发布紧急采购，3分钟左右您将得到回复。