- 您现在的位置：买卖IC网 > PDF目录4634 > LT1175MPQ#TRPBF (Linear Technology)IC REG LDO NEG ADJ .5A DDPAK-5 PDF资料下载
参数资料
| 型号： | LT1175MPQ#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/20页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO NEG ADJ .5A DDPAK-5 |
| 标准包装： | 750 |
| 稳压器拓扑结构： | 负，可调式 |
| 输出电压： | -3.8 V ~ -19.9 V |
| 输入电压： | -4.3 V ~ -20 V |
| 电压 - 压降（标准）： | 0.5V @ 500mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 500mA |
| 电流 - 限制（最小）： | 可调式 |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-6，D²Pak（5 引线+接片），TO-263BA |
| 供应商设备封装： | D2PAK-5 |
| 包装： | 带卷 (TR) |
LT1175
PIN FUNCTIONS
(N8/Q/ST/S8/T)
V IN (Pins 1, 8/Pin 3, Tab/Pin 2, Tab/Pins 1, 8/Pin 3, Tab):
Power is supplied to the device through this pin. A bypass
capacitor is required on this pin if the device is more than
six inches away from the main ?lter capacitor. In general,
the impedance of a battery rises with frequency, so it is
advisable to include a bypass capacitor in battery-powered
circuits. A 1μF or larger tantalum capacitor is suggested
for all applications, but if low ESR capacitors such as
ceramic or ?lm are used for the output and input capaci-
tors, the input capacitor should be three times the value
of the output capacitor.
I LIM2 , I LIM4 (Pins 2, 7/NA/NA/Pins 2, 7/NA): The two
current limit pins are emitter sections of the power transis-
tor. When left open, they ?oat several hundred millivolts
above the negative input voltage. When shorted to the
input voltage, they increase current limit by a minimum
of 200mA for I LIM2 and 400mA for I LIM4 . These pins must
be connected only to the input voltage, either directly or
through a resistor.
OUTPUT (Pin 3/Pin 1/Pin 1/Pin 3/Pin 1): The OUTPUT pin
is the collector of the NPN power transistor. It can be forced
to the input voltage, to ground or up to 2V positive with
respect to ground without damage or latchup (see Output
Voltage Reversal in Applications Information section). The
LT1175 has foldback current limit, so maximum current at
the OUTPUT pin is a function of input-to-output voltage.
See Typical Performance Characteristics.
SENSE (Pin 4/Pin 2/NA/Pin 4/Pin 2): The SENSE pin is
used in the adjustable version to allow custom selection
of output voltage, with an external divider set to generate
3.8V at the SENSE pin. Input bias current is typically 75nA
?owing out of the pin. Maximum forced voltage on the
SENSE pin is 2V and –10V with respect to GND pin.
The ?xed 5V version utilizes the SENSE pin to give true
Kelvin connections to the load or to drive an external pass
transistor for higher output currents. Bias current out
of the 5V SENSE pin is approximately 12μA. Separating
the SENSE and OUTPUT pins also allows for a new loop
compensation technique described in the Applications
Information section.
GND (Pin 5/Pin 4/Pin 3/Pin 5/Pin 4): The GND pin has a
quiescent current of 45μA at zero load current, increas-
ing by approximately 10μA per mA of output current. At
500mA output current, GND pin current is about 5mA.
Current ?ows into the GND pin.
SHDN (Pin 6/Pin 5/NA/Pin 6/Pin 5): The SHDN pin is
specially con?gured to allow it to be driven from either
positive voltage logic or with negative only logic. Forc-
ing the SHDN pin 2V either above or below the GND
pin will turn the regulator on. This makes it simple to
connect directly to positive logic signals for active low
shutdown. If no positive voltages are available, the
SHDN pin can be driven below the GND pin to turn the
regulator on. When left open, the SHDN pin will default
low to a regulator “on” condition . For all voltages below
absolute maximum ratings, the SHDN pin draws only a
few microamperes of current (see Typical Performance
Characteristics). Maximum voltage on the SHDN pin is 15V,
– 20V with respect to the GND pin and 35V, –5V with
respect to the negative input pin.
1175ff
8
相关PDF资料 |
PDF描述 |
|---|---|
| LT1175MPS8-5#TRPBF | IC REG LDO -5V .5A 8SOIC |
| MIC5305-1.8YD5 TR | IC REG LDO 1.8V .15A TSOT23-5 |
| FMC07DREI-S13 | CONN EDGECARD 14POS .100 EXTEND |
| HBC40DRXI | CONN EDGECARD 80POS DIP .100 SLD |
| RBB95DHRT | CONN CARD EXTEND 190POS .050" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1175MPS8#PBF | 功能描述:IC REG LDO NEG ADJ .5A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:8V 输入电压:10.5 V ~ 23 V 电压 - 压降（标准）:1.7V @ 40mA 稳压器数量:1 电流 - 输出:100mA（最小值） 电流 - 限制（最小）:- 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:剪切带 (CT) 产品目录页面:1075 (CN2011-ZH PDF) 其它名称:296-24390-1 |
| LT1175MPS8#TRPBF | 功能描述:IC REG LDO NEG ADJ .5A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:300mA（最小值） 电流 - 限制（最小）:360mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) |
| LT1175MPS8-5#PBF | 功能描述:IC REG LDO -5V .5A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3V 输入电压:最高 5.5V 电压 - 压降（标准）:0.12V @ 150mA 稳压器数量:1 电流 - 输出:150mA（最小值） 电流 - 限制（最小）:220mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) 其它名称:ADP160AUJZ-3.0-R7TR |
| LT1175MPS8-5#TRPBF | 功能描述:IC REG LDO -5V .5A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:300mA（最小值） 电流 - 限制（最小）:360mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) |
| LT1176 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Step-Down Switching Regulator |
发布紧急采购，3分钟左右您将得到回复。