- 您现在的位置：买卖IC网 > PDF目录13482 > LT1507IN8-3.3#PBF (Linear Technology)IC REG BUCK 3.3V 1.5A 8DIP PDF资料下载
参数资料
| 型号： | LT1507IN8-3.3#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 3.3V 1.5A 8DIP |
| 标准包装： | 50 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 3.3V |
| 输入电压： | 4 V ~ 15 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 包装： | 管件 |
| 供应商设备封装： | 8-PDIP |
LT1507
APPLICATIO N S I N FOR M ATIO N
be due to a radiated magnetic field coupling into PC
Table 1. Representative Surface Mount Units
board traces. But why were some boards bad and
others good? In a moment of desperation (or divine
inspiration) I unsoldered a “bad” inductor, rotated it
180 ° and resoldered it. Problem fixed!!
MANUFACTURER
Coiltronics
CTX5-1
CTX10-1
VALUE
( μ H)
5
10
DC
(A)
2.3
1.9
CORE SERIES
TYPE ( ? ) CORE
Tor 0.027 KM μ
Tor 0.039 KM μ
HEIGHT
(mm)
4.2
4.2
It turns out that the inductor was symmetrical in all
regards except that the polarity of the magnetic field
reversed when the unit was rotated 180 ° because
current flowed in the opposite direction in the coil. In
one direction, the magnetically induced ripple in the
board traces added to output ripple. Rotating the induc-
tor caused the induced field to reduce output ripple.
CTX5-1P
CTX10-1P
Sumida
CDRH64
CDRH73
CD73
CD104
Gowanda
SM20-102K
5
10
10
10
10
10
10
1.8
1.6
1.7
1.7
1.4
2.4
1.3
Tor
Tor
SC
SC
Open
Open
Open
0.021
0.030
0.084
0.055
0.062
0.041
0.038
52
52
Fer
Fer
Fer
Fer
Fer
4.2
4.2
4.5
3.4
3.5
4.0
7
Unfortunately the inductor had no physical package
Dale
assymmetry to indicate rotation, including part mark-
ing, so we had to visually examine the winding in each
IHSM-4825
IHSM-5832
10
10
3.1
4.3
Open
Open
0.071
0.053
Fer
Fer
5.6
7.1
unit before soldering it to the boards. This little horror
story should not preclude the use of open core induc-
tors, but it emphasizes the need to carefully check the
effect these seductively small, low cost inductors may
have on regulator or system performances.
4. Look for an inductor (see Table 1) which meets the
requirements of core shape, peak current (to avoid
saturation), average current (to limit heat) and fault
current (if the inductor gets too hot, wire insulation will
melt and cause turn-to-turn shorts). Keep in mind that
all good things like high efficiency, surface mounting,
low profile and high temperature operation will increase
cost, sometimes dramatically.
5. After making an initial choice, consider secondary things
like output voltage ripple, second sourcing, etc. Use the
experts in the Linear Technology Applications Depart-
ment if you feel uncertain about the final choice. They
have experience with a wide range of inductor types and
can tell you about the latest developments in low profile,
surface mounting, etc.
SC = Semi-closed geometry
Fer = Ferrite core material
52 = Type 52 powdered iron core material
KM μ = Kool M μ
OUTPUT CAPACITOR
The output capacitor is normally chosen by its effective
series resistance (ESR), because that is what determines
output ripple voltage. At 500kHz any polarized capacitor is
essentially resistive. To get low ESR takes volume ; physi-
cally larger capacitors have lower ESR. The ESR range
needed for typical LT1507 applications is 0.05 ? to 0.5 ? .
A typical output capacitor is an AVX type TPS, 100 μ F at
10V, with a guaranteed ESR less than 0.1 ? . This is a “D”
size surface mount solid tantalum capacitor. TPS capaci-
tors are specially constructed and tested for low ESR so
they give the lowest ESR for a given volume. The value in
microfarads is not particularly critical and values from
22 μ F to greater than 500 μ F work well, but you cannot
cheat mother nature on ESR. If you find a tiny 22 μ F solid
tantalum capacitor, it will have high ESR and output ripple
voltage will be terrible. The chart in Table 2 shows some
typical solid tantalum surface mount capacitors.
10
相关PDF资料 |
PDF描述 |
|---|---|
| RBA49DTAD | CONN EDGECARD 98POS R/A .125 SLD |
| MAX6771TAZD3+T | IC REG LINEAR 2.5V/ADJ 8-TDFN |
| VI-26Y-EV-F2 | CONVERTER MOD DC/DC 3.3V 99W |
| VI-26X-EX-F4 | CONVERTER MOD DC/DC 5.2V 75W |
| MAX664CPA+ | IC REG LDO -5V/ADJ 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1507IS8 | 功能描述:IC REG BUCK ADJ 1.5A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1507IS8#PBF | 功能描述:IC REG BUCK ADJ 1.5A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1507IS8#TR | 功能描述:IC REG BUCK ADJ 1.5A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1507IS8#TRPBF | 功能描述:IC REG BUCK ADJ 1.5A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1507IS8-3.3 | 功能描述:IC REG BUCK 3.3V 1.5A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。