- 您现在的位置：买卖IC网 > PDF目录13482 > LT1507IN8-3.3#PBF (Linear Technology)IC REG BUCK 3.3V 1.5A 8DIP PDF资料下载
参数资料
| 型号： | LT1507IN8-3.3#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 3.3V 1.5A 8DIP |
| 标准包装： | 50 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 3.3V |
| 输入电压： | 4 V ~ 15 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 包装： | 管件 |
| 供应商设备封装： | 8-PDIP |
LT1507
PI N FU N CTIO N S
saturation voltage and maximum duty cycle. A typical
value for minimum input voltage is 1V above output
voltage. Start-up conditions may require more voltage at
light loads. See Minimum Input Voltage for details.
V SW (Pin 3): The switch pin is driven up to the input voltage
in the ON state and is an open circuit in the OFF state. At
higher load currents, pin voltage during the off condition
will be one diode drop below ground as set by the external
catch diode. At lighter loads the pin will assume an
intermediate state equal to output voltage during part of
the switch OFF time. Maximum negative voltage on the
switch pin is 1V with respect to the GND pin, so it must
always be clamped with a catch diode to the GND pin.
SHDN (Pin 4): The shutdown pin is used to turn off the
regulator and to reduce input drain current to a few
microamperes. Actually this pin has two separate thresh-
olds, one at 2.38V to disable switching and a second at
0.4V to force complete micropower shutdown. The 2.38V
threshold functions as an accurate undervoltage lockout
(UVLO). This is sometimes used to prevent the regulator
from delivering power until the input voltage has reached
a predetermined level.
SYNC (Pin 5): The SYNC pin is used to synchronize the
internal oscillator to an external signal. It is directly logic
compatible and can be driven with any signal between
10% and 90% duty cycle. The synchronizing range is
equal to initial operating frequency up to 1MHz. See
Sychronizing section for details.
FB/SENSE (Pin 7): The feedback pin is used to set output
voltage using an external voltage divider that generates
2.42V at the pin with the desired output voltage. The fixed
voltage (– 3 .3V) parts have the divider included on the chip
and the feedback pin is used as a sense pin connected
directly to the 5V output. Two additional functions are
performed by the feedback pin. When the pin voltage
drops below 1.7V, switch current limit is reduced. Below
1V, switching frequency is also reduced. See More Than
Just Voltage Feedback.
V C (Pin 8): The V C pin is the output of the error amplifier
and the input of the peak switch current comparator. It is
normally used for frequency compensation but can do
double duty as a current clamp or control loop override.
This pin sets at about 1V for very light loads and 2V at
maximum load. It can be driven to ground to shut off the
regulator, but if driven high, current must be limited to 4mA.
BLOCK DIAGRA M
The LT1507 is a constant frequency, current mode buck
converter. This means that there is an internal clock and
two feedback loops that control the duty cycle of the power
switch. In addition to the normal error amplifier, there is
a current sense amplifier that monitors switch current on
a cycle-by-cycle basis. A switch cycle starts with an
oscillator pulse which sets the RS flip-flop to turn the
switch on. When switch current reaches a level set by the
inverting input of the comparator, the flip-flop is reset and
the switch turns off. Output voltage control is obtained by
using the output of the error amplifier to set the switch
current trip point. This technique means that the error
amplifier commands current to be delivered to the output
rather than voltage. A voltage fed system will have low
phase shift up to the resonant frequency of the inductor
6
and output capacitor, then an abrupt 180 ° shift will occur.
The current fed system will have 90 ° phase shift at a much
lower frequency, but will not have the additional 90 ° shift
until well beyond the LC resonant frequency. This makes
it much easier to frequency compensate the feedback loop
and also gives much quicker transient response.
High switch efficiency is attained by using the BOOST pin
to provide a voltage to the switch driver which is higher
than the input voltage, allowing the switch to be saturated.
This boosted voltage is generated with an external capaci-
tor and diode.
Two comparators are connected to the shutdown pin. One
has a 2.38V threshold for undervoltage lockout and the
second has a 0.4V threshold for complete shutdown.
相关PDF资料 |
PDF描述 |
|---|---|
| RBA49DTAD | CONN EDGECARD 98POS R/A .125 SLD |
| MAX6771TAZD3+T | IC REG LINEAR 2.5V/ADJ 8-TDFN |
| VI-26Y-EV-F2 | CONVERTER MOD DC/DC 3.3V 99W |
| VI-26X-EX-F4 | CONVERTER MOD DC/DC 5.2V 75W |
| MAX664CPA+ | IC REG LDO -5V/ADJ 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1507IS8 | 功能描述:IC REG BUCK ADJ 1.5A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1507IS8#PBF | 功能描述:IC REG BUCK ADJ 1.5A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1507IS8#TR | 功能描述:IC REG BUCK ADJ 1.5A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1507IS8#TRPBF | 功能描述:IC REG BUCK ADJ 1.5A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1507IS8-3.3 | 功能描述:IC REG BUCK 3.3V 1.5A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。