- 您现在的位置：买卖IC网 > PDF目录13482 > LT1507IN8-3.3#PBF (Linear Technology)IC REG BUCK 3.3V 1.5A 8DIP PDF资料下载
参数资料
| 型号： | LT1507IN8-3.3#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 3.3V 1.5A 8DIP |
| 标准包装： | 50 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 3.3V |
| 输入电压： | 4 V ~ 15 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 包装： | 管件 |
| 供应商设备封装： | 8-PDIP |
LT1507
APPLICATIO N S I N FOR M ATIO N
This is safe for short periods of time, but it would be
prudent to check with the diode manufacturer if continu-
ous operation under these conditions must be tolerated.
BOOST PIN CONSIDERATIONS
For most applications, the boost components are a 0.22 μ F
capacitor and an MBR0520 or BAT85 Schottky diode. This
capacitor value is twice that suggested for the LT1376
because the lower voltages commonly found in LT1507
applications may require lower ripple voltage across the
capacitor to ensure adequate boost voltage under worst-
case conditions. Efficiency is not affected by the capacitor
value, but the capacitor should have an ESR of less than
2 ? to ensure that it can be recharged fully under the worst-
case condition of minimum input voltage. Almost any type
of film or ceramic capacitor will work fine.
INPUT
The anode of the diode can be connected to the regulated
output voltage or the unregulated input voltage. The
“boost voltage” generated across the boost capacitor is
then nearly identical to the anode voltage. The input
connection minimizes start-up problems and gives plenty
of boost voltage, but efficiency is slightly lower, especially
with input voltages above 10V. For 5V to 3.3V operation,
or any output voltage less than 3.3V, the diode should be
connected to the input. With input voltage more than 3V
above the output and an output voltage of at least 3.3V the
output connection will give better efficiency. Use the
BAT85 Schottky diode for 3.3V applications where the
anode is connected to the output.
LAYOUT CONSIDERATIONS
Suggested layout for the LT1507 is shown in Figure 3. The
main concern for layout is to minimize the length of the
MINIMIZE AREA OF
CONNECTIONS TO THE
C2
D2
C F
SWITCH NODE AND
BOOST NODE, BUT OBSERVE
CURRENT DENSITY LIMITATIONS
IN PATH TO L1
C3
BOOST
IN
V C
FB
C C
R C
C F AND R C ARE OPTIONAL.
SEE FREQUENCY
COMPENSATION
KEEP INPUT CAPACITOR
AND CATCH DIODE CLOSE
TO REGULATOR AND
TERMINATE THEM
D1
SW
SHDN
GND
SYNC
R2
TO SAME POINT
R1
L1
SYNC
GROUND RING NEED
NOT BE AS SHOWN.
(NORMALLY EXISTS AS
INTERNAL PLANE)
CONNECT OUTPUT CAPACITOR
DIRECTLY TO HEAVY GROUND
C1
OUTPUT
TAKE OUTPUT DIRECTLY FROM END OF OUTPUT
CAPACITOR TO AVOID PARASITIC RESISTANCE
AND INDUCTANCE (KELVIN CONNECTION)
TERMINATE GND PIN
DIRECTLY TO GROUND
PLANE WITH VIA TO
MINIMIZE EMI. (MINIMIZE
DISTANCE TO INPUT
CAPACITOR C3). CONNECT
FEEDBACK RESISTORS AND
COMPENSATION
COMPONENTS DIRECTLY
TO GROUND PLANE OR TO
SWITCHER GND PIN.
LT1507 ? F03
Figure 3. Suggested Layout
13
相关PDF资料 |
PDF描述 |
|---|---|
| RBA49DTAD | CONN EDGECARD 98POS R/A .125 SLD |
| MAX6771TAZD3+T | IC REG LINEAR 2.5V/ADJ 8-TDFN |
| VI-26Y-EV-F2 | CONVERTER MOD DC/DC 3.3V 99W |
| VI-26X-EX-F4 | CONVERTER MOD DC/DC 5.2V 75W |
| MAX664CPA+ | IC REG LDO -5V/ADJ 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1507IS8 | 功能描述:IC REG BUCK ADJ 1.5A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1507IS8#PBF | 功能描述:IC REG BUCK ADJ 1.5A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1507IS8#TR | 功能描述:IC REG BUCK ADJ 1.5A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1507IS8#TRPBF | 功能描述:IC REG BUCK ADJ 1.5A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1507IS8-3.3 | 功能描述:IC REG BUCK 3.3V 1.5A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。