参数资料
| 型号： | LT1762EMS8-3.3#TR |
| 厂商： | Linear Technology |
| 文件页数： | 13/16页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V .15A 8MSOP |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V |
| 输入电压： | 最高 20V |
| 电压 - 压降（标准）： | 0.27V @ 150mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 150mA |
| 电流 - 限制（最小）： | 160mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
LT1762 Series
APPLICATIO N S I N FOR M ATIO N
significant enough to drop capacitor values below appro-
priate levels. Capacitor DC bias characteristics tend to
improve as component case size increases, but expected
capacitance at operating voltage should be verified.
Voltage and temperature coefficients are not the only
sources of problems. Some ceramic capacitors have a
piezoelectric response. A piezoelectric device generates
voltage across its terminals due to mechanical stress,
similar to the way a piezoelectric accelerometer or micro-
phone works. For a ceramic capacitor the stress can be
induced by vibrations in the system or thermal transients.
The resulting voltages produced can cause appreciable
amounts of noise, especially when a ceramic capacitor is
used for noise bypassing. A ceramic capacitor produced
Figure 6’s trace in response to light tapping from a pencil.
LT1762-5
C OUT = 10 μ F
C BYP = 0.01 μ f
I LOAD = 100mA
V OUT
500 μ V/DIV
The GND pin current can be found by examining the GND
Pin Current curves in the Typical Performance Character-
istics. Power dissipation will be equal to the sum of the two
components listed above.
The LT1762 series regulators have internal thermal limit-
ing designed to protect the device during overload condi-
tions. For continuous normal conditions, the maximum
junction temperature rating of 125 ° C must not be
exceeded. It is important to give careful consideration to
all sources of thermal resistance from junction to ambient.
Additional heat sources mounted nearby must also be
considered.
For surface mount devices, heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Copper board stiffeners and plated
through-holes can also be used to spread the heat gener-
ated by power devices.
The following table lists thermal resistance for several
different board sizes and copper areas. All measurements
were taken in still air on 3/32" FR-4 board with one ounce
copper.
Table 1. Measured Thermal Resistance
100ms/DIV
1762 F05
COPPER AREA
THERMAL RESISTANCE
2500mm
2500mm
2500mm
Figure 6. Noise Resulting from Tapping on a Ceramic Capacitor
TOPSIDE*
2
BACKSIDE
2
BOARD AREA
2
(JUNCTION-TO-AMBIENT)
110 ° C/W
2500mm
Similar vibration induced behavior can masquerade as
1000mm
2
2
2500mm
2
115 ° C/W
increased output voltage noise.
225mm 2
2500mm 2
2500mm 2
120 ° C/W
100mm
2500mm
50mm
2500mm
Thermal Considerations
The power handling capability of the device will be limited
by the maximum rated junction temperature (125 ° C). The
2 2
2 2
*Device is mounted on topside.
2500mm
2500mm
2
2
130 ° C/W
140 ° C/W
power dissipated by the device will be made up of two
components:
1. Output current multiplied by the input/output voltage
differential: (I OUT )(V IN – V OUT ), and
2. GND pin current multiplied by the input voltage:
(I GND )(V IN ).
Calculating Junction Temperature
Example: Given an output voltage of 3.3V, an input voltage
range of 4V to 6V, an output current range of 0mA to 50mA
and a maximum ambient temperature of 50 ° C, what will
the maximum junction temperature be?
The power dissipated by the device will be equal to:
I OUT(MAX) (V IN(MAX) – V OUT ) + I GND (V IN(MAX) )
1762fa
13
相关PDF资料 |
PDF描述 |
|---|---|
| LT1763MPDE-2.5#PBF | IC REG LDO 2.5V .5A 12-DFN |
| LT1764AMPQ#TRPBF | IC REG LDO ADJ 3A DDPAK-5 |
| LT1765EFE-1.8 | IC REG BUCK 1.8V 3A 16TSSOP |
| LT1766HFE#TRPBF | IC REG BUCK ADJ 1.5A 16TSSOP |
| LT1767EMS8-2.5 | IC REG BUCK 2.5V 1.5A 8MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1762EMS8-5 | 功能描述:IC REG LDO 5V .15A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:0.1V @ 200mA 稳压器数量:2 电流 - 输出:300mA 电流 - 限制（最小）:350mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-UFQFN 供应商设备封装:8-MLPQ-UT（1.5x1.5） 包装:剪切带 (CT) 产品目录页面:1358 (CN2011-ZH PDF) 其它名称:SC560HULCT |
| LT1762EMS8-5#PBF | 功能描述:IC REG LDO 5V .15A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:MIC5365/66 Ultra-small LDO Regulators 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3V 输入电压:最高 5.5V 电压 - 压降（标准）:0.155V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:200mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:4-UDFN 裸露焊盘，4-TMLF? 供应商设备封装:4-TMLF?（1x1） 包装:Digi-Reel® 其它名称:576-3192-6 |
| LT1762EMS8-5#TR | 功能描述:IC REG LDO 5V .15A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:0.1V @ 200mA 稳压器数量:2 电流 - 输出:300mA 电流 - 限制（最小）:350mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-UFQFN 供应商设备封装:8-MLPQ-UT（1.5x1.5） 包装:剪切带 (CT) 产品目录页面:1358 (CN2011-ZH PDF) 其它名称:SC560HULCT |
| LT1762EMS8-5#TRPBF | 功能描述:IC REG LDO 5V .15A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:0.1V @ 200mA 稳压器数量:2 电流 - 输出:300mA 电流 - 限制（最小）:350mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-UFQFN 供应商设备封装:8-MLPQ-UT（1.5x1.5） 包装:剪切带 (CT) 产品目录页面:1358 (CN2011-ZH PDF) 其它名称:SC560HULCT |
| LT1762EMS8-5PBF | 制造商:Linear Technology 功能描述:LDO Regulator 5V 150mA Low Noise MSOP8 |
发布紧急采购，3分钟左右您将得到回复。