参数资料
| 型号： | LT1762EMS8-3.3#TR |
| 厂商： | Linear Technology |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V .15A 8MSOP |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V |
| 输入电压： | 最高 20V |
| 电压 - 压降（标准）： | 0.27V @ 150mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 150mA |
| 电流 - 限制（最小）： | 160mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
LT1762 Series
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are T A = 25 ° C. (Note 2)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Dropout Voltage
V IN = V OUT(NOMINAL)
(Notes 5, 6)
I LOAD = 1mA
I LOAD = 1mA
I LOAD = 10mA
I LOAD = 10mA
I LOAD = 50mA
I LOAD = 50mA
I LOAD = 150mA
I LOAD = 150mA
●
●
●
●
0.09
0.15
0.21
0.27
0.15
0.19
0.21
0.25
0.27
0.31
0.33
0.40
V
V
V
V
V
V
V
V
GND Pin Current
V IN = V OUT(NOMINAL)
(Notes 5, 7)
Output Voltage Noise
ADJ Pin Bias Current
Shutdown Threshold
SHDN Pin Current
(Note 9)
Quiescent Current in Shutdown
Ripple Rejection
I LOAD = 0mA
I LOAD = 1mA
I LOAD = 10mA
I LOAD = 50mA
I LOAD = 150mA
C OUT = 10 μ F, C BYP = 0.01 μ F, I LOAD = 150mA, BW = 10Hz to 100kHz
(Notes 3, 8)
V OUT = Off to On
V OUT = On to Off
V SHDN = 0V
V SHDN = 20V
V IN = 6V, V SHDN = 0V
V IN – V OUT = 1V (Avg), V RIPPLE = 0.5V P-P , f RIPPLE = 120Hz,
●
●
●
●
●
●
●
0.25
50
25
70
350
1.3
4
20
30
0.8
0.65
0.1
1
0.1
65
65
120
500
1.8
7
100
2
1
μ A
μ A
μ A
mA
mA
μ V RMS
nA
V
V
μ A
μ A
μ A
dB
I LOAD = 150mA
Current Limit
Input Reverse Leakage Current
V IN = 7V, V OUT = 0V
V IN = V OUT(NOMINAL) + 1V, ? V OUT = – 0.1V
V IN = – 20V, V OUT = 0V
●
●
160
400
1
mA
mA
mA
Reverse Output Current
(Note 10)
LT1762-2.5
LT1762-3
LT1762-3.3
LT1762-5
LT1762 (Note 3)
V OUT = 2.5V, V IN < 2.5V
V OUT = 3V, V IN < 3V
V OUT = 3.3V, V IN < 3.3V
V OUT = 5V, V IN < 5V
V OUT = 1.22V, V IN < 1.22V
10
10
10
10
5
20
20
20
20
10
μ A
μ A
μ A
μ A
μ A
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT1762 regulators are tested and specified under pulse load
conditions such that T J ≈ T A . The LT1762 is 100% tested at 25 ° C.
Performance at – 40 ° C and 125 ° C is assured by design, characterization
and correlation with statistical process controls.
Note 3: The LT1762 (adjustable version) is tested and specified for these
conditions with the ADJ pin connected to the OUT pin.
Note 4: Operating conditions are limited by maximum junction
temperature. The regulated output voltage specification will not apply for
all possible combinations of input voltage and output current. When
operating at maximum input voltage, the output current range must be
limited. When operating at maximum output current, the input voltage
range must be limited.
Note 5: To satisfy requirements for minimum input voltage, the LT1762
(adjustable version) is tested and specified for these conditions with an
external resistor divider (two 250k resistors) for an output voltage of
2.44V. The external resistor divider will add a 5 μ A DC load on the output.
Note 6: Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a specified output current. In dropout, the
output voltage will be equal to: V IN – V DROPOUT .
Note 7: GND pin current is tested with V IN = V OUT(NOMINAL) and a current
source load. This means the device is tested while operating in its dropout
region. This is the worst-case GND pin current. The GND pin current will
decrease slightly at higher input voltages.
Note 8: ADJ pin bias current flows into the ADJ pin.
Note 9: SHDN pin current flows into the SHDN pin.
Note 10: Reverse output current is tested with the IN pin grounded and the
OUT pin forced to the rated output voltage. This current flows into the OUT
pin and out the GND pin.
1762fa
3
相关PDF资料 |
PDF描述 |
|---|---|
| LT1763MPDE-2.5#PBF | IC REG LDO 2.5V .5A 12-DFN |
| LT1764AMPQ#TRPBF | IC REG LDO ADJ 3A DDPAK-5 |
| LT1765EFE-1.8 | IC REG BUCK 1.8V 3A 16TSSOP |
| LT1766HFE#TRPBF | IC REG BUCK ADJ 1.5A 16TSSOP |
| LT1767EMS8-2.5 | IC REG BUCK 2.5V 1.5A 8MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1762EMS8-5 | 功能描述:IC REG LDO 5V .15A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:0.1V @ 200mA 稳压器数量:2 电流 - 输出:300mA 电流 - 限制（最小）:350mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-UFQFN 供应商设备封装:8-MLPQ-UT（1.5x1.5） 包装:剪切带 (CT) 产品目录页面:1358 (CN2011-ZH PDF) 其它名称:SC560HULCT |
| LT1762EMS8-5#PBF | 功能描述:IC REG LDO 5V .15A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:MIC5365/66 Ultra-small LDO Regulators 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3V 输入电压:最高 5.5V 电压 - 压降（标准）:0.155V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:200mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:4-UDFN 裸露焊盘，4-TMLF? 供应商设备封装:4-TMLF?（1x1） 包装:Digi-Reel® 其它名称:576-3192-6 |
| LT1762EMS8-5#TR | 功能描述:IC REG LDO 5V .15A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:0.1V @ 200mA 稳压器数量:2 电流 - 输出:300mA 电流 - 限制（最小）:350mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-UFQFN 供应商设备封装:8-MLPQ-UT（1.5x1.5） 包装:剪切带 (CT) 产品目录页面:1358 (CN2011-ZH PDF) 其它名称:SC560HULCT |
| LT1762EMS8-5#TRPBF | 功能描述:IC REG LDO 5V .15A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:0.1V @ 200mA 稳压器数量:2 电流 - 输出:300mA 电流 - 限制（最小）:350mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-UFQFN 供应商设备封装:8-MLPQ-UT（1.5x1.5） 包装:剪切带 (CT) 产品目录页面:1358 (CN2011-ZH PDF) 其它名称:SC560HULCT |
| LT1762EMS8-5PBF | 制造商:Linear Technology 功能描述:LDO Regulator 5V 150mA Low Noise MSOP8 |
发布紧急采购，3分钟左右您将得到回复。