- 您现在的位置：买卖IC网 > PDF目录13904 > LT1765ES8 (Linear Technology)IC REG BUCK ADJ 3A 8SOIC PDF资料下载
参数资料
| 型号： | LT1765ES8 |
| 厂商： | Linear Technology |
| 文件页数： | 8/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 3A 8SOIC |
| 标准包装： | 100 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.2 V ~ 20 V |
| 输入电压： | 3 V ~ 25 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.25MHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 8-SOIC |
LT1765/LT1765-1.8/LT1765-2.5/
LT1765-3.3/LT1765-5
APPLICATIONS INFORMATION
FB RESISTOR NETWORK
If an output voltage of 1.8V, 2.5V, 3.3V or 5V is required,
the respective ?xed option part, -1.8, -2.5, -3.3 or -5,
should be used. The FB pin is tied directly to the output;
the necessary resistive divider is already included on
the part. For other voltage outputs, the adjustable part
should be used and an external resistor divider added.
The suggested resistor (R2) from FB to ground is 10k.
This reduces the contribution of FB input bias current to
output voltage to less than 0.25%. The formula for the
resistor (R1) from V OUT to FB is:
rating and turn-on surge problems. Y5V or similar type
ceramics can be used since the absolute value of capaci-
tance is less important and has no signi?cant effect on
loop stability. If operation is required close to the minimum
input required by the output or the LT1765, a larger value
may be required. This is to prevent excessive ripple caus-
ing dips below the minimum operating voltage resulting
in erratic operation.
If tantalum capacitors are used, values in the 22μF to 470μF
range are generally needed to minimize ESR and meet
ripple current and surge ratings. Care should be taken to
R 1 =
R 2 ( V OUT – 1 . 2 )
1 . 2 – R 2 ( 0 . 25 μ A )
ensure the ripple and surge ratings are not exceeded. The
AVX TPS and Kemet T495 series tantalum capacitors are
surge rated. AVX recommends derating capacitor operating
voltage by 2:1 for high surge applications.
LT1765 (ADJ)
V SW
ERROR
OUTPUT
OUTPUT CAPACITOR
AMPLIFIER
+
1.2V
Unlike the input capacitor, RMS ripple current in the output
–
FB
R1
+
R2
capacitor is normally low enough that ripple current rating
is not an issue. The current waveform is triangular, with
an RMS value given by:
( )( ) f ( V IN )
V C
GND
10k
Figure 2. Feedback Network
1765 F02
I RIPPLE ( RMS ) =
0.29 ( V OUT ) ( V IN ? V OUT )
L
The LT1765 will operate with both ceramic and tantalum
I RIPPLE ( RMS ) = I OUT OUT ( V IN ? V OUT ) / V IN 2
INPUT CAPACITOR
Step-down regulators draw current from the input supply
in pulses. The rise and fall times of these pulses are very
fast. The input capacitor is required to reduce the voltage
ripple at the input of LT1765 and to force the switching
current into a tight local loop, thereby minimizing EMI.
The RMS ripple current can be calculated from:
V
Ceramic capacitors are ideal for input bypassing. At higher
switching frequency, the energy storage requirement of
the input capacitor is reduced so values in the range of
1μF to 4.7μF are suitable for most applications. Their high
output capacitors. Ceramic capacitors are generally cho-
sen for their small size, very low ESR (effective series
resistance), and good high frequency operation. Ceramic
output capacitors in the 1μF to 10μF range, X7R or X5R
type are recommended.
Tantalum capacitors are usually chosen for their bulk
capacitance properties, useful in high transient load ap-
plications. ESR rather than absolute value de?nes output
ripple at 1.25MHz. Typical LT1765 applications require a
tantalum capacitor with less than 0.3Ω ESR at 22μF to
500μF, see Table 2. This ESR provides a useful zero in the
frequency response. Ceramic output capacitors with low
ESR usually require a larger V C capacitor or an additional
series R to compensate for this.
frequency capacitive nature removes most ripple current
1765fd
8
相关PDF资料 |
PDF描述 |
|---|---|
| HM53-40710HLF | HIGH POWER LOW COST INDUCTORS |
| VE-J3J-EY-S | CONVERTER MOD DC/DC 36V 50W |
| RBA28DTKH-S288 | CONN EDGECARD 56POS .125 EXTEND |
| LT3508IUF#TRPBF | IC REG BUCK ADJ 1.4A DL 24QFN |
| HM53-40710VLF | HIGH POWER LOW COST INDUCTORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1765ES8#PBF | 功能描述:IC REG BUCK ADJ 3A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT1765ES8#TR | 功能描述:IC REG BUCK ADJ 3A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1765ES8#TRPBF | 功能描述:IC REG BUCK ADJ 3A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1765ES8PBF | 制造商:Linear Technology 功能描述:LT1765 adj 3A Buck SD dc-dc converter |
| LT1766 | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.4A, 500kHz Step-Down Switching Regulator |
发布紧急采购，3分钟左右您将得到回复。