- 您现在的位置：买卖IC网 > PDF目录14048 > LT1767EMS8-1.8#TRPBF (Linear Technology)IC REG BUCK 1.8V 1.5A 8MSOP PDF资料下载
参数资料
| 型号： | LT1767EMS8-1.8#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 1.8V 1.5A 8MSOP |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 1.8V |
| 输入电压： | 3 V ~ 25 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.25MHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-MSOP |
LT1767/LT1767-1.8/
LT1767-2.5/LT1767-3.3/LT1767-5
APPLICATIO N S I N FOR M ATIO N
FB RESISTOR NETWORK
If an output voltage of 1.8V, 2.5V, 3.3V or 5V is required, the
respective fixed option part, -1.8, -2.5, -3.3 or -5, should be
used. The FB pin is tied directly to the output; the necessary
resistive divider is already included on the part. For other
voltage outputs, the adjustable part should be used and an
external resistor divider added. The suggested resistor (R2)
from FB to ground is 10k. This reduces the contribution of
FB input bias current to output voltage to less than 0.25%.
The formula for the resistor (R1) from V OUT to FB is:
of capacitance is less important and has no significant
effect on loop stability. If operation is required close to the
minimum input required by the output of the LT1767, a
larger value may be required. This is to prevent excessive
ripple causing dips below the minimum operating voltage,
resulting in erratic operation.
If tantalum capacitors are used, values in the 22 μ F to 470 μ F
range are generally needed to minimize ESR and meet ripple
current and surge ratings. Care should be taken to ensure
the ripple and surge ratings are not exceeded. The AVX TPS
R 1 =
R 2 ( V OUT ? 1 . 2 )
1 . 2 ? R 2 ( 0 . 25 μ A )
and Kemet T495 series are surge rated. AVX recommends
derating capacitor operating voltage by 2:1 for high surge
applications.
LT1767
ERROR
V SW
OUTPUT
OUTPUT CAPACITOR
Unlike the input capacitor, RMS ripple current in the output
AMPLIFIER
+
–
1.2V
FB
R1
+
capacitor is normally low enough that ripple current rating
is not an issue. The current waveform is triangular, with an
RMS value given by:
( )( )( ) IN V
V C
GND
R2
10k
1767 F02
I RIPPLE ( RMS ) =
0 . 29 ( V OUT ) ( V IN ? V OUT
L f
)
Figure 2. Feedback Network
INPUT CAPACITOR
Step-down regulators draw current from the input supply in
pulses. The rise and fall times of these pulses are very fast.
The input capacitor is required to reduce the voltage ripple
this causes at the input of LT1767 and force the switching
current into a tight local loop, thereby minimizing EMI. The
RMS ripple current can be calculated from:
The LT1767 will operate with both ceramic and tantalum
output capacitors. Ceramic capacitors are generally chosen
for their small size, very low ESR (effective series resis-
tance), and good high frequency operation, reducing out-
put ripple voltage. Their low ESR removes a useful zero in
the loop frequency response, common to tantalum capaci-
tors. To compensate for this, the V C loop compensation
pole frequency must typically be reduced by a factor of 10.
Typical ceramic output capacitors are in the 1 μ F to 10 μ F
I RIPPLE ( RMS ) = I OUT V OUT ( V IN ? V OUT
) / V IN 2
range. Since the absolute value of capacitance defines the
pole frequency of the output stage, an X7R or X5R type
ceramic, which have good temperature stability, is recom-
Higher value, lower cost ceramic capacitors are now avail-
able in smaller case sizes. These are ideal for input bypass-
ing since their high frequency capacitive nature removes
most ripple current rating and turn-on surge problems. At
higher switching frequency, the energy storage require-
ment of the input capacitor is reduced so values in the range
of 1 μ F to 4.7 μ F are suitable for most applications. Y5V or
similar type ceramics can be used since the absolute value
mended.
Tantalum capacitors are usually chosen for their bulk
capacitance properties, useful in high transient load appli-
cations. ESR rather than capacitive value defines output
ripple at 1.25MHz. Typical LT1767 applications require a
tantalum capacitor with less than 0.3 ? ESR at 22 μ F to
500 μ F, see Table 2.
sn1767 1767fas
7
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6868UK46D3S+T | IC MPU SUPERVISOR SOT23-5 |
| 50MH70.47MEFCT54X7 | CAP ALUM 0.47UF 50V 20% RADIAL |
| MAX6868UK45D4L+T | IC MPU SUPERVISOR SOT23-5 |
| LT1767EMS8-5#TRPBF | IC REG BUCK 5V 1.5A 8MSOP |
| 50MH70.47MEFCTZ4X7 | CAP ALUM 0.47UF 50V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1767EMS8-2.5 | 功能描述:IC REG BUCK 2.5V 1.5A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1767EMS8-2.5#PBF | 功能描述:IC REG BUCK 2.5V 1.5A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT1767EMS8-2.5#TR | 功能描述:IC REG BUCK 2.5V 1.5A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1767EMS8-2.5#TRPBF | 功能描述:IC REG BUCK 2.5V 1.5A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1767EMS8-3.3 | 功能描述:IC REG BUCK 3.3V 1.5A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。