- 您现在的位置：买卖IC网 > PDF目录15300 > LT1952IGN#TRPBF (Linear Technology)IC REG CTRLR ISO PWM CM 16-SSOP PDF资料下载
参数资料
| 型号： | LT1952IGN#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR ISO PWM CM 16-SSOP |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 560kHz |
| 占空比： | 90% |
| 电源电压： | 9.25 V ~ 25 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT1952/LT1952-1
OPERATION
Slope Compensation
The current mode architecture requires slope compensa-
tion to be added to the current sensing loop to prevent
subharmonic oscillations which can occur for duty cycles
above 50%. Unlike most current mode converters which
have a slope compensation ramp that is fixed internally,
placing a constraint on inductor value and operating
frequency, the LT1952/LT1952-1 have externally adjust-
able slope compensation. Slope compensation can be
programmed by inserting an external resistor (R SLOPE )
in series with the I SENSE pin. The LT1952/LT1952-1 have
a linear slope compensation ramp which sources current
out of the I SENSE pin of approximately 8μA at 0% duty
cycle to 35μA at 80% duty cycle.
Overcurrent Detection and Soft-Start (OC Pin)
An added feature to the LT1952/LT1952-1 is a precise
100mV sense threshold at the OC pin used to detect
overcurrent conditions in the converter and set a soft-start
APPLICATIONS INFORMATION
latch. The OC pin is connected directly to the source of
the primary side MOSFET to monitor peak current in the
MOSFET (Figure 7). The 107mV threshold is constant
over the entire duty cycle range of the converter because
it is unaffected by the slope compensation added to the
I SENSE pin.
Synchronizing
A SYNC pin allows the LT1952/LT1952-1 oscillator to be
synchronized to an external clock. The SYNC pin can be
driven from a logic level output, requiring less than 0.8V
for a logic level low and greater than 2.2V for a logic level
high. Duty cycle should run between 10% and 90%. To
avoid loss of slope compensation during synchroniza-
tion, the free running oscillator frequency (f OSC ) should
be programmed to 80% of the external clock frequency
(f SYNC ). The R SLOPE resistor chosen for non-synchronized
operation should be increased by 1.25x (= f SYNC /f OSC ).
Shutdown and Programming Undervoltage Lockout
The LT1952/LT1952-1 have an accurate 1.32V shutdown
threshold at the SD_V SEC pin. This threshold can be
used in conjunction with a resistor divider to define the
undervoltage lockout threshold (UVLO) of the system
input voltage (V S ) to the power converter (Figure 3). A pin
current hysteresis (10μA before part turn on, 0μA after
part turn on) allows UVLO hysteresis to be programmed.
Calculation of the ON/OFF thresholds for the supply (SV IN )
to the power converter can be made as follows:
OPTIONAL
SHUTDOWN
TRANSISTOR
ON OFF
SYSTEM
INPUT (V S )
R1
R2
SD_V SEC
11μA
1.32V
–
+
LT1952/LT1952-1
1952 F03
V S OFF Threshold = 1.32[1 + (R1/R2)]
V S ON Threshold = SV IN OFF + (10μA ? R1)
A simple open drain transistor can be added to the resistor
divider network at the SD_V SEC pin to control the turn off
of the LT1952/LT1952-1 (Figure 3).
The SD_V SEC pin must not be left open since there must
be an external source current >10μA to lift the pin past its
1.32V threshold for part turn on.
Figure 3. Programming Undervoltage Lockout (UVLO)
Micropower Start-Up: Selection of Start-Up Resistor
and Capacitor for V IN
The LT1952/LT1952-1 use turn-on voltage hysteresis at
the V IN pin and low start-up current to allow micro-power
start-up (Figure 4). The LT1952/LT1952-1 monitor V IN pin
voltage to allow part turn on at 14.25V (7.75V LT1952-1)
and part turn off at 8.75V (6.5V LT1952-1). Low start-up
19521fe
13
相关PDF资料 |
PDF描述 |
|---|---|
| SLP153M010A5P3 | CAP ALUM 15000UF 10V 20% SNAP |
| VE-25L-EW-F3 | CONVERTER MOD DC/DC 28V 100W |
| SLP103M016C1P3 | CAP ALUM 10000UF 16V 20% SNAP |
| AS1901-C31-T | IC SUPERVISOR ACT LOW SOT23-3 |
| IMC1210EB47NJ | INDUCTOR WW 47NH 5% 1210 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1952MPGN#PBF | 功能描述:IC REG CTRLR ISO PWM CM 16-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LT1952MPGN#TRPBF | 功能描述:IC REG CTRLR ISO PWM CM 16-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LT1952MPGN-1#PBF | 功能描述:IC REG CTRLR ISO PWM CM 16-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LT1952MPGN-1#TRPBF | 功能描述:IC REG CTRLR ISO PWM CM 16-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LT1956 | 制造商:LINEAR 制造商全称:LINEAR 功能描述:100V Synchronous Switching Regulator Controller |
发布紧急采购，3分钟左右您将得到回复。