参数资料
| 型号： | LT1970IFE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 3/26页 |
| 文件大小： | 0K |
| 描述： | IC OP AMP 500MA ADJ 20-TSSOP |
| 标准包装： | 2,500 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 转换速率： | 1.6 V/µs |
| 增益带宽积： | 3.6MHz |
| 电流 - 输入偏压： | 160nA |
| 电压 - 输入偏移： | 200µV |
| 电流 - 电源： | 7mA |
| 电流 - 输出 / 通道： | 800mA |
| 电压 - 电源，单路/双路(±)： | 5 V ~ 36 V，±2.5 V ~ 18 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 20-TSSOP-EP |
| 包装： | 带卷 (TR) |
LT1970
11
1970fc
APPLICATIONS INFORMATION
its very high transconductance, takes control from the input
stage, GM1. The output current is regulated to a value of
IOUT = VSENSE/RSENSE = (VCSRC or VCSNK)/(10 RSENSE).
The time required for the current limit ampliers to take
control of the output is typically 4μs.
Linear operation of the current limit sense amplier occurs
with the inputs SENSE+ and SENSE– ranging between VCC
– 1.5V and VEE + 1.5V. Most applications will connect pins
SENSE+ and OUT together, with the load on the opposite
side of the external sense resistor and pin SENSE–. Feed-
back to the inverting input of GM1 should be connected
from SENSE– to – IN. Ground side sensing of load current
may be employed by connecting the load between pins
OUT and SENSE+. Pin SENSE– would be connected to
ground in this instance. Load current would be regulated
in exactly the same way as the conventional connection.
However, voltage mode accuracy would be degraded in
this case due to the voltage across RSENSE.
Creative applications are possible where pins SENSE+ and
SENSE– monitor a parameter other than load current. The
operating principle that at most one of the current limit
stages may be active at one time, and that when active,
the current limit stages take control of the output from
GM1, can be used for many different signals.
Current Limit Threshold Control Buffers
Input pins VCSNK and VCSRC are used to set the response
thresholds of current limit ampliers “ISINK” and “ISRC”.
Each of these inputs may be independently driven by a
voltage of 0V to 5V above the COMMON reference pin.
The 0V to 5V input voltage is attenuated by a factor of 10
and applied as an offset to the appropriate current limit
amplier. AC signals may be applied to these pins. The AC
bandwidth from a VC pin to the output is typically 2MHz.
For proper operation of the LT1970, these control inputs
cannot be left oating.
For low VCC supply applications it is important to keep
the maximum input control voltages, VCSRC and VCSNK,
at least 2.5V below the VCC potential. This ensures linear
control of the current limit threshold. Reducing the current
limit sense resistor value allows high output current from
a smaller control voltage which may be necessary if the
VCC supply is only 5V.
The transfer function from VC to the associated VOS is
linear from about 0.1V to 5V in, or 10mV to 500mV at
the current limit amplier inputs. An intentional nonlinear-
ity is built into the transfer functions at low levels. This
nonlinearity insures that both the sink and source limit
ampliers cannot become active simultaneously. Simul-
taneous activation of the limit ampliers could result in
uncontrolled outputs. As shown in the Typical Performance
Characteristics curves, the control inputs have a “hockey
stick” shape, to keep the minimum limit threshold at 4mV
for each limit amplier.
Figure 1 illustrates an interesting use of the current
sense input pins. Here the current limit control ampli-
ers are used to produce a symmetrically limited output
voltage swing. Instead of monitoring the output current,
the output voltage is divided down by a factor of 20 and
applied to the SENSE+ input, with the SENSE– input
grounded. When the threshold voltage between SENSE+
and SENSE– (VCLAMP/10) is reached, the current limit
stage takes control of the output and clamps it a level of
±2 VCLAMP. With control inputs VCSRC and VCSNK tied
together, a single polarity input voltage sets the same +
and – output limit voltage for symmetrical limiting. In this
circuit the output will current limit at the built-in fail-safe
level of typically 800mA.
Figure 1. Symmetrical Output Voltage Limiting
VCSRC
COMMON
VEE
VCSNK
V–
FILTER
V+
12V
EN
VCC
ISNK
ISRC
SENSE–
SENSE+
TSD
OUT
+IN
R3
3k
80mV
TO
10V
–80mV
TO
–10V
±CLAMP
REACHED
OUTPUT CLAMPS
AT 2× VCLAMP
VCLAMP
OV TO 5V
VIN
LT1970
–12V
–IN
R1
21.5k
RL
1970 F01
R2
1.13k
RF
RG
相关PDF资料 |
PDF描述 |
|---|---|
| LT1990AHS8#TRPBF | IC AMP DIFF +/-250V MCRPWR 8SOIC |
| LT1993CUD-10#TRPBF | IC DIFF AMP/ADC DRVR 16-QFN |
| LT1993CUD-2#PBF | IC DIFF AMP/ADC DRVR 16-QFN |
| LT1993CUD-4#TRPBF | IC DIFF AMP/ADC DRVR 16-QFN |
| LT1994MPDD#TRPBF | IC DIFF AMP/DRIVER LN 8-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1976 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic Dual Tracking 3A Step-Down Switching |
| LT1976B | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage 1.5A, 200kHz Step-Down Switching Regulator with 100μA Quiescent Current |
| LT1976BEFE | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 2.4V to 60V 16-Pin TSSOP EP |
| LT1976BEFE#PBF | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT1976BEFE#TRPBF | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。