参数资料
型号: LT3439EFE#PBF
厂商: Linear Technology
文件页数: 4/12页
文件大小: 0K
描述: IC REG PSH-PLL CTRLR ISO 16TSSOP
标准包装: 95
类型: 推挽式控制器,隔离式
输出数: 1
输入电压: 2.8 V ~ 17.5 V
频率 - 开关: 20kHz ~ 250kHz
电流 - 输出: 1A
同步整流器:
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 16-TSSOP(0.173",4.40mm)裸露焊盘
包装: 管件
供应商设备封装: 16-TSSOP-EP
产品目录页面: 1331 (CN2011-ZH PDF)
LT3439
PI FU CTIO S
PGND (Pins 1, 16): Power ground is connected to the
emitter of the power switches via an internal sense resis-
tor. It has large currents flowing through it and should be
connected to a good quality ground plane.
COL A, COL B (Pins 3, 14): These are the open collectors
of the output power switches. They are connected to the
outer terminals of the center tap transformer. Large cur-
rents flow into these pins so external traces should be kept
as short as possible.
R SL (Pin 4): The slew control resistor sets the maximum
current and voltage slew rate for the collectors A and B.
The minimum resistor value is 3.4k for fast slewing and the
maximum resistor is 34k for slow slewing. For more
details, see “Slew Rate Setting” in the Applications Infor-
mation section of this data sheet.
SYNC (Pin 5): The SYNC pin can be used to synchronize
the oscillator to an external clock. R T and C T should be set
such that the oscillator clock frequency is approximately
10% below the external clock frequency. If unused, this
pin should be tied to GND. For more details, see “Oscillator
Sync” in the Applications Information section of this data
sheet.
C T (Pin 6): The oscillator capacitor pin is used in conjunc-
tion with the R T pin to set the oscillator frequency. For
R T = 16.9k, C T can be calculated as follows:
R T (Pin 7): The oscillator resistor pin is used to set the
charge and discharge currents of the oscillator capacitor.
The nominal value is 16.9k. The resistance can be adjusted
between ± 25% of nominal for better frequency accuracy.
SHDN (Pin 11): The SHDN pin is used to shut down the
part. Grounding this pin will disable all internal circuitry.
Increasing the SHDN voltage above the turn-on threshold
will enable the part. At the turn-on threshold, approxi-
mately 20 μ A of current is sourced out of the pin. This
current, in conjunction with the Thevenin resistance on the
pin, sets up the hysteresis. This allows the user to set the
undervoltage lockout (UVLO) of the supply and the amount
of start-up hysteresis with a resistor divider off of the input
voltage. Above 2.1V on the SHDN pin, the hysteresis
current is reduced to zero. If unused the pin can be left
floating or tied directly to the input voltage.
GND (Pin 10): Signal Ground. The oscillator, slew control
circuitry and the internal regulator are referred to signal
ground. Internally, signal ground is tied to substrate and
the exposed backside of the device. Connect the GND pin
to the ground plane and keep the connection free of large
currents.
V IN (Pin 13): This is the supply pin for the part and should
be bypassed with a 4.7 μ F or greater, low ESR capacitor.
When V IN ≤ 2.5V, an internal undervoltage lockout circuit
will trip and turn both outputs off.
C T (nF) = 70/f OSC (kHz)
The transformer operating frequency and the frequency
of each output is one half of the frequency of the oscillator.
sn3439 3439fs
4
相关PDF资料
PDF描述
RCM31DRMH CONN EDGECARD 62POS .156 WW
LTC3428EDD#PBF IC REG BOOST ADJ 4A 10DFN
LTC3421EUF#PBF IC REG BOOST SYNC ADJ 1.5A 24QFN
LT3501EFE#PBF IC REG BUCK ADJ 3A DL 20TSSOP
LT3508EFE#PBF IC REG BUCK ADJ 1.4A DL 16TSSOP
相关代理商/技术参数
参数描述
LT343L 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic
LT344L 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic
LT344LR 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic
LT3460 制造商:LINER 制造商全称:Linear Technology 功能描述:1.3MHz Step-Up DC/DC Converter in SC70 and ThinSOT
LT3460EDC-1#PBF 制造商:Linear Technology 功能描述:SP-SWREG/Monolithic, CUT TAPE 150mA, 650kHz Boost Converter in 2x2 DFN