- 您现在的位置：买卖IC网 > PDF目录14465 > LT3505IMS8E#PBF (Linear Technology)IC REG BUCK ADJ 1.2A 8MSOP PDF资料下载
参数资料
| 型号： | LT3505IMS8E#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.2A 8MSOP |
| 标准包装： | 50 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.78 V ~ 33.8 V |
| 输入电压： | 3.6 V ~ 36 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz ~ 3.01MHz |
| 电流 - 输出： | 1.2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 8-MSOP-EP |
LT3505
APPLICATIONS INFORMATION
Inductor Selection and Maximum Output Current
A good ?rst choice for the inductor value is:
L = 1.2 (V OUT + V D )/f SW
where V D is the voltage drop of the catch diode (~0.4V),
L is in μH and f SW is in MHz. With this value there will
be no subharmonic oscillation for applications with 50%
or greater duty cycle. The inductor’s RMS current rating
must be greater than your maximum load current and
its saturation current should be about 30% higher. For
robust operation in fault conditions, the saturation current
should be above 2.2A. To keep ef?ciency high, the series
resistance (DCR) should be less than 0.1 . Table 2 lists
several vendors and types that are suitable.
Of course, such a simple design guide will not always
result in the optimum inductor for your application. A
larger value provides a higher maximum load current and
reduces output voltage ripple at the expense of slower
transient response. If your load is lower than 1.2A, then
you can decrease the value of the inductor and operate
with higher ripple current. This allows you to use a physi-
cally smaller inductor, or one with a lower DCR resulting
in higher ef?ciency. There are several graphs in the Typical
Performance Characteristics section of this data sheet that
show the maximum load current as a function of input
voltage and inductor value for several popular output volt-
ages. Low inductance may result in discontinuous mode
operation, which is okay, but further reduces maximum
load current. For details on maximum output current and
discontinuous mode operation, see Linear Technology
Application Note 44.
Table 2. Inductor Vendors
Catch Diode
Depending on load current, a 1A to 2A Schottky diode is
recommended for the catch diode, D1. The diode must
have a reverse voltage rating equal to or greater than the
maximum input voltage. The ON Semiconductor MBRM140
is a good choice; it is rated for 1A continuous forward
current and a maximum reverse voltage of 40V.
Input Capacitor
The input of the LT3505 circuit must be bypassed with a
X7R or X5R type ceramic capacitor. Y5V types have poor
performance over temperature and applied voltage and
should not be used. For switching frequencies higher than
750kHz, bypass the input with a 1μF or higher value ceramic
capacitor. For switching frequencies below 750kHz, bypass
the input with a 2.2 μ F or higher value ceramic capacitor.
If the input power source has high impedance, or there is
signi?cant inductance due to long wires or cables, additional
bulk capacitance may be necessary. This can be provided
with a low performance electrolytic capacitor.
Step-down regulators draw current from the input sup-
ply in pulses with very fast rise and fall times. The input
capacitor is required to reduce the resulting voltage
ripple at the LT3505 and to force this very high frequency
switching current into a tight local loop, minimizing EMI.
To accomplish this task, the input bypass capacitor must
be placed close to the LT3505 and the catch diode; see
the PCB Layout section. A second precaution regarding
the ceramic input capacitor concerns the maximum input
voltage rating of the LT3505. A ceramic input capacitor
combined with trace or cable inductance forms a high
quality (underdamped) tank circuit. If the LT3505 circuit
is plugged into a live supply, the input voltage can ring to
VENDOR
Sumida
Toko
Würth Elektronik
URL
www.sumida.com
www.toko.com
www.we-online.com
PART SERIES
CDRH4D28
CDRH5D28
CDRH5D28
A916CY
D585LC
WE-TPC(M)
WE-PD2(M)
WE-PD(S)
INDUCTANCE RANGE (μH)
1.2 to 4.7
2.5 to 10
2.5 to 33
2 to 12
1.1 to 39
1 to 10
2.2 to 22
1 to 27
Size (mm)
4.5 × 4.5
5.5 × 5.5
8.3 × 8.3
6.3 × 6.2
8.1 × 8.0
4.8 × 4.8
5.2 × 5.8
7.3 × 7.3
3505fc
13
相关PDF资料 |
PDF描述 |
|---|---|
| LT1304CS8#PBF | IC REG BOOST ADJ 0.2A 8SOIC |
| RSM15DTMD-S189 | CONN EDGECARD 30POS R/A .156 SLD |
| LT1109CS8#PBF | IC REG BOOST ADJ 0.1A 8SOIC |
| HC2-R68TR-R | INDUCTOR PWR HI CURR 0.68UH SMD |
| VI-J5W-EX-B1 | CONVERTER MOD DC/DC 5.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3505IMS8E-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.2A, Step-Down Switching Regulator in 3mm × 3mm DFN |
| LT3505IMS8E-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.2A, Step-Down Switching Regulator in 3mm × 3mm DFN |
| LT3506 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic Dual Tracking 3A Step-Down Switching |
| LT3506A | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic Dual Tracking 3A Step-Down Switching |
| LT3506AEDHD | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Monolithic 1.6A Step-Down Switching Regulator |
发布紧急采购，3分钟左右您将得到回复。