- 您现在的位置：买卖IC网 > PDF目录14797 > LT3506AIDHD#PBF (Linear Technology)IC REG BUCK ADJ 1.6A DL 16DFN PDF资料下载
参数资料
| 型号： | LT3506AIDHD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.6A DL 16DFN |
| 标准包装： | 73 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.8 V ~ 22 V |
| 输入电压： | 3.6 V ~ 25 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.1MHz |
| 电流 - 输出： | 1.6A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-DFN（5x4） |
| 产品目录页面： | 1331 (CN2011-ZH PDF) |
LT3506/LT3506A
APPLICATIONS INFORMATION
tor must have low impedance at the switching frequency
to do this effectively, and it must have an adequate ripple
current rating. With two switchers operating at the same
frequency but with different phases and duty cycles, cal-
culating the input capacitor RMS current is not simple.
However, a conservative value is the RMS input current for
the channel that is delivering most power (V OUT ? I OUT ).
This is given by:
22μF (10μF for the LT3506A) will be required to meet the
ESR and ripple current requirements. Because the input
capacitor is likely to see high surge currents when the input
source is applied, tantalum capacitors should be surge
rated. The manufacturer may also recommend operation
below the rated voltage of the capacitor. Be sure to place
the 1μF ceramic as close as possible to the V IN and GND
pins on the IC for optimal noise immunity.
< OUT
I INRMS = I OUT
V OUT ? ( V IN ? V OUT )
V IN
I
2
A ?nal caution is in order regarding the use of ceramic
capacitors at the input. A ceramic input capacitor can
combine with stray inductance to form a resonant tank
and is largest when V IN = 2V OUT (50% duty cycle). As
the second, lower power channel draws input current,
the input capacitor’s RMS current actually decreases as
the out-of-phase current cancels the current drawn by
the higher power channel. Considering that the maximum
load current from a single channel is ~1.6A, RMS ripple
current will always be less than 0.8A.
The high frequency of the LT3506 reduces the energy
storage requirements of the input capacitor, so that the
capacitance required is less than 22μF (less than 10μF
for the LT3506A). The combination of small size and low
impedance (low equivalent series resistance or ESR) of
ceramic capacitors makes them the preferred choice.
The low ESR results in very low voltage ripple and the
capacitors can handle plenty of ripple current. They are also
comparatively robust and can be used in this application
at their rated voltage. X5R and X7R types are stable over
temperature and applied voltage, and give dependable
service. Other types (Y5V and Z5U) have very large tem-
perature and voltage coef?cients of capacitance, so they
may have only a small fraction of their nominal capacitance
in your application. While they will still handle the RMS
ripple current, the input voltage ripple may become fairly
large, and the ripple current may end up ?owing from
your input supply or from other bypass capacitors in your
system, as opposed to being fully sourced from the local
input capacitor.
An alternative to a high value ceramic capacitor is a lower
value along with a larger electrolytic capacitor, for example
a 1μF ceramic capacitor in parallel with a low ESR tantalum
circuit. If power is applied quickly (for example by plug-
ging the circuit into a live power source) this tank can ring,
doubling the input voltage and damaging the LT3506. The
solution is to either clamp the input voltage or dampen the
tank circuit by adding a lossy capacitor in parallel with the
ceramic capacitor. For details, see Application Note 88.
Output Capacitor Selection
The output capacitor ?lters the inductor current to gen-
erate an output with low voltage ripple. It also stores
energy in order satisfy transient loads and to stabilize the
LT3506’s control loop. Because the LT3506 operates at a
high frequency, you don’t need much output capacitance.
Also, the current mode control loop doesn’t require the
presence of output capacitor series resistance (ESR). For
these reasons, you are free to use ceramic capacitors to
achieve very low output ripple and small circuit size.
Estimate output ripple with the following equations:
V RIPPLE = Δ I L /(8 ? f ? C OUT ) for ceramic capacitors
V RIPPLE = Δ I L ? ESR for electrolytic capacitors (tantalum
and aluminum)
where Δ I L is the peak-to-peak ripple current in the induc-
tor. The RMS content of this ripple is very low, and the
RMS current rating of the output capacitor is usually not
of concern.
Another constraint on the output capacitor is that it must
have greater energy storage than the inductor; if the stored
energy in the inductor is transferred to the output, you
would like the resulting voltage step to be small compared
capacitor. For the electrolytic capacitor, a value larger than
3506afc
10
相关PDF资料 |
PDF描述 |
|---|---|
| 9230-94-RC | CHOKE RF MOLDED .1UH 10%PHENOLIC |
| LTC3603EUF#PBF | IC REG BUCK SYNC ADJ 2.5A 20QFN |
| 1140-2R2M | CHOKE RF RADIAL 2.2UH 20% |
| LGU1K182MELB | CAP ALUM 1800UF 80V 20% SNAP |
| LGU2P471MELB | CAP ALUM 470UF 220V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3506AIDHD-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Monolithic 1.6A Step-Down Switching Regulator |
| LT3506AIDHD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Monolithic 1.6A Step-Down Switching Regulator |
| LT3506AIFE | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Monolithic 1.6A Step-Down Switching Regulator |
| LT3506AIFE#PBF | 功能描述:IC REG BUCK ADJ 1.6A DL 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3506AIFE#TRPBF | 功能描述:IC REG BUCK ADJ 1.6A DL 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。