参数资料
型号: LT3757IMSE#PBF
厂商: Linear Technology
文件页数: 22/36页
文件大小: 0K
描述: IC REG CTRLR PWM CM 10-MSOP
产品培训模块: LT3757 and LT3758 - Boost, Flyback, SEPIC and Inverting Controllers
标准包装: 50
PWM 型: 电流模式
输出数: 1
频率 - 最大: 1MHz
电源电压: 2.9 V ~ 40 V
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: -40°C ~ 125°C
封装/外壳: 10-TFSOP,10-MSOP(0.118",3.00mm 宽)裸露焊盘
包装: 管件
LT3757/LT3757A
APPLICATIONS INFORMATION
I SW(MAX) = I L1(MAX) + I L2(MAX) = I O(MAX) ?
SEPICConverter:SwitchDutyCycleandFrequency
For a SEPIC converter operating in CCM, the duty cycle
of the main switch can be calculated based on the output
voltage (V OUT ), the input voltage (V IN ) and the diode
forward voltage (V D ).
The maximum duty cycle (D MAX ) occurs when the converter
has the minimum input voltage:
In a SEPIC converter, the switch current is equal to I L1 +
I L2 when the power switch is on, therefore, the maximum
average switch current is defined as:
1
1 ? D MAX
and the peak switch current is:
I SW(PEAK) = ? 1 + ? ? I O(MAX) ?
D MAX =
V OUT + V D
V IN(MIN) + V OUT + V D
? 2 ?
? c ?
1
1 ? D MAX
I L1(MAX) = I IN(MAX) = I O(MAX) ?
SEPICConverter:InductorandSenseResistorSelection
As shown in Figure 1, the SEPIC converter contains two
inductors: L1 and L2. L1 and L2 can be independent, but can
also be wound on the same core, since identical voltages
are applied to L1 and L2 throughout the switching cycle.
For the SEPIC topology, the current through L1 is the
converter input current. Based on the fact that, ideally, the
output power is equal to the input power, the maximum
average inductor currents of L1 and L2 are:
D MAX
1 ? D MAX
I L2(MAX) = I O(MAX)
The constant c in the preceding equations represents the
percentage peak-to-peak ripple current in the switch, rela-
tive to I SW(MAX) , as shown in Figure 9. Then, the switch
ripple current ?I SW can be calculated by:
?I SW = c ? I SW(MAX)
The inductor ripple currents ?I L1 and ?I L2 are identical:
?I L1 = ?I L2 = 0.5 ? ? I SW
The inductor ripple current has a direct effect on the
choice of the inductor value. Choosing smaller values of
?I L requires large inductances and reduces the current
loop gain (the converter will approach voltage mode).
Accepting larger values of ?I L allows the use of low in-
ductances, but results in higher input current ripple and
greater core losses. It is recommended that c falls in the
range of 0.2 to 0.4.
I SW
I SW(MAX)
? I SW = χ ? I SW(MAX)
DT S
t
T S
3757 F08
Figure 9. The Switch Current Waveform of the SEPIC Converter
3757afd
22
相关PDF资料
PDF描述
RGM18DTKH CONN EDGECARD 36POS DIP .156 SLD
IDCS2512ER102M INDUCTOR POWER 1000UH 0.15A SMD
LTC1147CN8-5 IC REG CTRLR BUCK PWM CM 8-DIP
ADM805LAN IC SUPERVISOR 4.65V WD 8DIP
RYM18DTKD CONN EDGECARD 36POS DIP .156 SLD
相关代理商/技术参数
参数描述
LT3757IMSE-TRPBF 制造商:LINER 制造商全称:Linear Technology 功能描述:Boost, Flyback, SEPIC and Inverting Controller
LT3757MPMSE 制造商:LINER 制造商全称:Linear Technology 功能描述:Boost, Flyback, SEPIC and Inverting Controller
LT3757MPMSE#PBF 功能描述:IC REG CTRLR PWM CM 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LT3757MPMSE#TRPBF 功能描述:IC REG CTRLR PWM CM 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LT3757MPMSE-PBF 制造商:LINER 制造商全称:Linear Technology 功能描述:Boost, Flyback, SEPIC and Inverting Controller