参数资料
型号: LT3757IMSE#PBF
厂商: Linear Technology
文件页数: 23/36页
文件大小: 0K
描述: IC REG CTRLR PWM CM 10-MSOP
产品培训模块: LT3757 and LT3758 - Boost, Flyback, SEPIC and Inverting Controllers
标准包装: 50
PWM 型: 电流模式
输出数: 1
频率 - 最大: 1MHz
电源电压: 2.9 V ~ 40 V
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: -40°C ~ 125°C
封装/外壳: 10-TFSOP,10-MSOP(0.118",3.00mm 宽)裸露焊盘
包装: 管件
LT3757/LT3757A
APPLICATIONS INFORMATION
V IN(MIN)
0.5 ? ? I SW ? f
Givenanoperatinginputvoltagerange,andhavingchosen
the operating frequency and ripple current in the inductor,
the inductor value (L1 and L2 are independent) of the SEPIC
converter can be determined using the following equation:
L1 = L2 = ? D MAX
For most SEPIC applications, the equal inductor values
will fall in the range of 1μH to 100μH.
Based on the preceding equations, the user should choose
the inductors having sufficient saturation and RMS cur-
rent ratings.
In a SEPIC converter, when the power switch is turned on,
the current flowing through the sense resistor (I SENSE ) is
the switch current.
Set the sense voltage at I SENSE(PEAK) to be the minimum
of the SENSE current limit threshold with a 20% margin.
The sense resistor value can then be calculated to be:
By making L1 = L2, and winding them on the same core, the
value of inductance in the preceding equation is replaced
by 2L, due to mutual inductance:
R SENSE =
80 mV
I SW(PEAK)
V IN(MIN)
? I SW ? f
L = ? D MAX
This maintains the same ripple current and energy storage
in the inductors. The peak inductor currents are:
I L1(PEAK) = I L1(MAX) + 0.5 ? ? I L1
I L2(PEAK) = I L2(MAX) + 0.5 ? ? I L2
The RMS inductor currents are:
SEPIC Converter: Power MOSFET Selection
For the SEPIC configuration, choose a MOSFET with a
V DC rating higher than the sum of the output voltage and
input voltage by a safety margin (a 10V safety margin is
usually sufficient).
The power dissipated by the MOSFET in a SEPIC con-
verter is:
P FET = I 2SW(MAX) ? R DS(ON) ? D MAX
? I L1
c L1 =
I L1(RMS) = I L1(MAX) ? 1 +
where:
I L1(MAX)
I L2(RMS) = I L2(MAX) ? 1 +
c 2L1
12
c 2L2
12
+ 2 ? ( V IN(MIN) + V OUT ) 2 ? I L(MAX) ? C RSS ? f /1A
The first term in this equation represents the conduction
losses in the device, and the second term, the switching
loss. C RSS is the reverse transfer capacitance, which is
usually specified in the MOSFET characteristics.
For maximum efficiency, R DS(ON) and C RSS should be
minimized. From a known power dissipated in the power
MOSFET, its junction temperature can be obtained using
the following equation:
where:
c L2 =
? I L2
I L2 (MAX)
T J = T A + P FET ? θ JA = T A + P FET ? ( θ JC + θ CA )
T J must not exceed the MOSFET maximum junction
temperature rating. It is recommended to measure the
MOSFET temperature in steady state to ensure that absolute
maximum ratings are not exceeded.
3757afd
23
相关PDF资料
PDF描述
RGM18DTKH CONN EDGECARD 36POS DIP .156 SLD
IDCS2512ER102M INDUCTOR POWER 1000UH 0.15A SMD
LTC1147CN8-5 IC REG CTRLR BUCK PWM CM 8-DIP
ADM805LAN IC SUPERVISOR 4.65V WD 8DIP
RYM18DTKD CONN EDGECARD 36POS DIP .156 SLD
相关代理商/技术参数
参数描述
LT3757IMSE-TRPBF 制造商:LINER 制造商全称:Linear Technology 功能描述:Boost, Flyback, SEPIC and Inverting Controller
LT3757MPMSE 制造商:LINER 制造商全称:Linear Technology 功能描述:Boost, Flyback, SEPIC and Inverting Controller
LT3757MPMSE#PBF 功能描述:IC REG CTRLR PWM CM 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LT3757MPMSE#TRPBF 功能描述:IC REG CTRLR PWM CM 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LT3757MPMSE-PBF 制造商:LINER 制造商全称:Linear Technology 功能描述:Boost, Flyback, SEPIC and Inverting Controller