- 您现在的位置：买卖IC网 > PDF目录15313 > LT3800EFE#TRPBF (Linear Technology)IC REG CTRLR INV PWM CM 16-TSSOP PDF资料下载
参数资料
| 型号： | LT3800EFE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 6/24页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR INV PWM CM 16-TSSOP |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 220kHz |
| 占空比： | 95% |
| 电源电压： | 4 V ~ 60 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 是 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 带卷 (TR) |
LT3800
PIN FUNCTIONS
and reverse-current inhibit functions are enabled. When
the pin voltage is above 0.5V, Burst Mode operation is dis-
abled, but reverse-current inhibit operation is maintained.
DC/DC converters operating with reverse-current inhibit
operation (BURST_EN = V FB ) have a 1mA minimum load
requirement. Reverse-current inhibit is disabled when the
pin voltage is above 2.5V. This pin is typically shorted to
ground to enable Burst Mode operation and reverse-current
inhibit, shorted to V FB to disable Burst Mode operation
while enabling reverse-current inhibit, and connected
to V CC pin to disable both functions. See Applications
Information section.
V FB (Pin 6): Error Ampli?er Inverting Input. The noninvert-
ing input of the error ampli?er is connected to an internal
1.231V reference. Desired converter output voltage (V OUT )
is programmed by connecting a resistive divider from the
converter output to the V FB pin. Values for the resistor
connected from V OUT to V FB (R2) and the resistor con-
nected from V FB to ground (R1) can be calculated via the
following relationship:
V C pin is set at 100mV below the burst threshold, which
limits the negative excursion of the pin voltage. There-
fore, this pin cannot be pulled low with a low-impedance
source. If the V C pin must be externally manipulated, do
so through a 1kΩ series resistance.
SENSE – (Pin 8): Negative Input for Current Sense Ampli-
?er. Sensed inductor current limit set at ±150mV across
SENSE inputs.
SENSE + (Pin 9): Positive Input for Current Sense Ampli-
?er. Sensed inductor current limit set at ±150mV across
SENSE inputs.
PGND (Pin 10): High Current Ground Reference for Syn-
chronous Switch. Current path from pin to negative terminal
of V CC decoupling capacitor must not corrupt SGND.
BG (Pin 11): Synchronous Switch Gate Drive Output.
V CC (Pin 12): Internal Regulator Output. Most IC func-
tions are powered from this pin. Driving this pin from
an external source reduces V IN pin current to 20μA.
This pin is decoupled with a low ESR 1μF capacitor to
R2 = R1?
V OUT
1.231
–1
PGND. In shutdown mode, this pin sinks 20μA until the
pin voltage is discharged to 0V. See Typical Performance
Characteristics.
The V FB pin input bias current is 25nA, so use of extremely
high value feedback resistors could cause a converter
output that is slightly higher than expected. Bias current
error at the output can be estimated as:
? V OUT(BIAS) = 25nA ? R2
V C (Pin 7): Error Ampli?er Output. The voltage on the V C
pin corresponds to the maximum (peak) switch current per
oscillator cycle. The error ampli?er is typically con?gured
as an integrator by connecting an RC network from this
pin to ground. This network creates the dominant pole for
the converter voltage regulation feedback loop. Speci?c
integrator characteristics can be con?gured to optimize
transient response. Connecting a 100pF or greater high
frequency bypass capacitor from this pin to ground is also
recommended. When Burst Mode operation is enabled (see
NC (Pin 13): No Connection.
SW (Pin 14): Reference for V BOOST Supply and High Cur-
rent Return for Bootstrapped Switch.
TG (Pin 15): Bootstrapped Switch Gate Drive Output.
BOOST (Pin 16): Bootstrapped Supply – Maximum Operat-
ing Voltage (Ground Referred) to 75V. This pin is decoupled
with a low ESR 1μF capacitor to pin SW. The voltage on
the decoupling capacitor is refreshed through a recti?er
from either V CC or an external source.
Exposed Package Backside (SGND) (Pin 17): Low Noise
Ground Reference. SGND connection is made through
the exposed lead frame on back of TSSOP package which
must be soldered to the PCB ground.
Pin 5 description), an internal low impedance clamp on the
3800fc
6
相关PDF资料 |
PDF描述 |
|---|---|
| VI-2WD-EW-F1 | CONVERTER MOD DC/DC 85V 100W |
| UVK1A472MHD | CAP ALUM 4700UF 10V 20% RADIAL |
| VI-2WB-EY-B1 | CONVERTER MOD DC/DC 95V 50W |
| PCF1E470MCL1GS | CAP ALUM 47UF 25V 20% SMD |
| ECA43DCBI | CONN EDGECARD 86POS R/A .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3800IFE | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 4V to 60V 16-Pin TSSOP EP |
| LT3800IFE#PBF | 功能描述:IC REG CTRLR INV PWM CM 16-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LT3800IFE#PBF | 制造商:Linear Technology 功能描述:IC SYNC STEP-DOWN REGULATOR CTRL 16-TSSO |
| LT3800IFE#TR | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 4V to 60V 16-Pin TSSOP EP T/R |
| LT3800IFE#TRPBF | 功能描述:IC REG CTRLR INV PWM CM 16-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
发布紧急采购，3分钟左右您将得到回复。