- 您现在的位置：买卖IC网 > PDF目录15500 > LTC1142CG (Linear Technology)IC REG CTRLR BUCK PWM CM 28-SSOP PDF资料下载
参数资料
| 型号： | LTC1142CG |
| 厂商： | Linear Technology |
| 文件页数： | 12/20页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 28-SSOP |
| 标准包装： | 47 |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 250kHz |
| 占空比： | 100% |
| 电源电压： | 3.5 V ~ 18 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 1332 (CN2011-ZH PDF) |
LTC1142/LTC1142L/LTC1142HV
APPLICATIO S I FOR ATIO
[ V ( V ) ]
? V
dead-time, which could cost as much as 1% in efficiency
(although there are no other harmful effects if D1 and D2
are omitted). Therefore, D1 and D2 should be selected for
a forward voltage of less than 0.6V when conducting I MAX .
C IN and C OUT Selection
In continuous mode, the source current of the P-channel
MOSFET is a square wave of duty cycle V OUT / V IN . To
prevent large voltage transients, a low ESR input capaci-
tor sized for the maximum RMS current must be used. The
maximum RMS capacitor current is given by:
1 / 2
OUT IN OUT
C IN Required I RMS ≈ I MAX
V IN
This formula has a maximum at V IN = 2V OUT , where
I RMS = I OUT /2. This simple worst case conditon is com-
monly used for design because even significant deviations
do not offer much relief. Note that capacitor manufacturer’s
ripple current ratings are often based on only 2000 hours
of life. This makes it advisable to further derate the
capacitor, or to choose a capacitor rated at a higher
temperature than required. Several capacitors may also be
paralleled to meet size or height requirements in the
from Sanyo has the lowest ESR/size ratio of any aluminum
electrolytic at a somewhat higher price. Once the ESR
requirement for C OUT has been met, the RMS current
rating generally far exceeds the I RIPPLE(P-P) requirement.
In surface mount applications multiple capacitors may
have to be parallel to meet the capacitance, ESR or RMS
current handling requirements of the application. Alumi-
num electrolytic and dry tantalum capacitors are both
available in surface mount configurations. In the case of
tantalum, it is critical that the capacitors are surge tested
for use in switching power supplies. An excellent choice
is the AVX TPS series of surface mount tantalums, avail-
able in case heights ranging from 2mm to 4mm. For
example, if 200 μ F/10V is called for in an application
requiring 3mm height, two AVX 100 μ F/10V (P/N TPSD
107K010) could be used. Consult the manufacturer for
other specific recommendations.
At low supply voltages, a minimum capacitance at C OUT is
needed to prevent an abnormal low frequency operating
mode (see Figure 4). When C OUT is made too small, the
output ripple at low frequencies will be large enough to trip
the voltage comparator. This causes Burst Mode opera-
tion to be activated when the LTC1142 would normally be
in continuous operation. The output remains in regulation
design. Always consult the manufacturer if there is any
question. An additional 0.1 μ F to 1 μ F ceramic capacitor is
also required on each V IN line (Pins 10 and 24) for high
frequency decoupling.
The selection of C OUT is driven by the required Effective
Series Resistance (ESR). The ESR of C OUT must be less
than twice the value of R SENSE for proper operation of the
LTC1142:
C OUT Required ESR < 2R SENSE
Optimum efficiency is obtained by making the ESR equal
at all times.
1000
800
600
400
200
L = 50 μ H
R SENSE = 0.02 ?
L = 25 μ H
R SENSE = 0.02 ?
L = 50 μ H
R SENSE = 0.05 ?
to R SENSE . As the ESR is increased up to 2R SENSE , the
efficiency degrades by less than 1%. If the ESR is greater
0
0
1
2 3
V IN – V OUT VOLTAGE (V)
4
5
than 2R SENSE , the voltage ripple on the output capacitor
will prematurely trigger Burst Mode operation, resulting in
disruption of continuous mode and an efficiency hit which
can be several percent.
Manufacturers such as Nichicon and United Chemicon
should be considered for high performance capacitors.
The OS-CON semiconductor dielectric capacitor available
12
1142 F04
Figure 4. Minimum Value of C OUT
Checking Transient Response
The regulator loop response can be checked by looking
at the load transient response. Switching regulators take
several cycles to respond to a step in DC (resistive) load
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JTM-EY-B1 | CONVERTER MOD DC/DC 10V 50W |
| SPD62-823M | INDUCTOR PWR SHIELDED 82.0UH SMD |
| VI-JT1-EY-B1 | CONVERTER MOD DC/DC 12V 50W |
| VI-J5N-EY-B1 | CONVERTER MOD DC/DC 18.5V 50W |
| VI-J5L-EY-B1 | CONVERTER MOD DC/DC 28V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1142CG#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 包装:带卷 (TR) |
| LTC1142CG#TR | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1142CG#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1142HV | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual High Efficiency Synchronous Step-Down Switching Regulators |
| LTC1142HV-ADJ | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual High Efficiency Synchronous Step-Down Switching Regulators |
发布紧急采购，3分钟左右您将得到回复。