- 您现在的位置：买卖IC网 > PDF目录15500 > LTC1142CG (Linear Technology)IC REG CTRLR BUCK PWM CM 28-SSOP PDF资料下载
参数资料
| 型号： | LTC1142CG |
| 厂商： | Linear Technology |
| 文件页数： | 9/20页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 28-SSOP |
| 标准包装： | 47 |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 250kHz |
| 占空比： | 100% |
| 电源电压： | 3.5 V ~ 18 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 1332 (CN2011-ZH PDF) |
LTC1142/LTC1142L/LTC1142HV
OPERATIO
Refer to Functional Diagram
As the load current increases, the output voltage de-
creases slightly. This causes the output of the gain stage
[Pin 27(13)] to increase the current comparator thresh-
old, thus tracking the load current.
The sequence of events for Burst Mode operation is very
similar to continuous operation with the cycle interrupted
by the voltage comparator. When the output voltage is at
or above the desired regulated value, the P-channel
MOSFET is held off by comparator V and the timing
capacitor continues to discharge below V TH1 . When the
timing capacitor discharges past V TH2 , voltage compara-
tor S trips, causing the internal sleep line to go low and the
N-channel MOSFET to turn off.
The circuit now enters sleep mode with both power
MOSFETs turned off. In sleep mode a majority of the
circuitry is turned off, dropping the quiescent current
from 1.6mA to 160 μ A (for one regulator block). The load
current is now being supplied from the output capacitor.
When the output voltage has dropped by the amount of
hysteresis in comparator V, the P-channel MOSFET is
again turned on and this process repeats.
To avoid the operation of the current loop interfering with
Burst Mode operation, a built-in offset V OS is incorporated
in the gain stage. This prevents the current comparator
threshold from increasing until the output voltage has
dropped below a minimum threshold.
To prevent both the external MOSFETs from ever being
turned on at the same time, feedback is incorporated to
sense the state of the driver output pins. Before the NDrive
output can go high, the PDrive output must also be high.
Likewise, the PDrive output is prevented from going low
while the NDrive output is high.
Using constant off-time architecture, the operating fre-
quency is a function of the input voltage. To minimize the
frequency variation as dropout is approached, the off-time
controller increases the discharge current as V IN drops
below V OUT + 1.5V. In dropout the P-channel MOSFET is
turned on continuously (100% duty cycle) providing low
dropout operation with V OUT ~ V IN .
APPLICATIO S I FOR ATIO
The basic LTC1142 application circuit is shown in
Figure 1. External component selection is driven by the
load requirement and begins with the selection of R SENSE .
Once R SENSE is known, C T and L can be chosen. Next, the
power MOSFETs and D1 are selected. Finally, C IN and
C OUT are selected and the loop is compensated. Since the
3.3V and 5V sections in the LTC1142 are identical and
similarly section 1 and section 2 in the LTC1142HV-ADJ/
LTC1142L-ADJ are identical, the process of component
selection is the same for both sections. The circuit shown
in Figure 1 can be configured for operation up to an input
yielding a maximum output current I MAX equal to the peak
value less half the peak-to-peak ripple current. For proper
Burst Mode operation, I RIPPLE(P-P) must be less than or
equal to the minimum current comparator threshold.
Since efficiency generally increases with ripple current,
the maximum allowable ripple current is assumed, i.e.,
I RIPPLE(P-P) = 25mV/R SENSE (see C T and L Selection for
Operating Frequency section). Solving for R SENSE and
allowing a margin for variations in the LTC1142 and
external component values yields:
voltage of 20V.
R SENSE Selection for Output Current
R SENSE =
100mV
I MAX
R SENSE is chosen based on the required output current.
The LTC1142 current comparators have a threshold range
which extends from a minimum of 25mV/R SENSE to a
maximum of 150mV/R SENSE . The current comparator
A graph for Selecting R SENSE vs Maximum Output Current
is given in Figure 2.
The load current below which Burst Mode operation com-
mences, I BURST , and the peak short-circuit current I SC(PK) ,
threshold sets the peak of the inductor ripple current,
9
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JTM-EY-B1 | CONVERTER MOD DC/DC 10V 50W |
| SPD62-823M | INDUCTOR PWR SHIELDED 82.0UH SMD |
| VI-JT1-EY-B1 | CONVERTER MOD DC/DC 12V 50W |
| VI-J5N-EY-B1 | CONVERTER MOD DC/DC 18.5V 50W |
| VI-J5L-EY-B1 | CONVERTER MOD DC/DC 28V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1142CG#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 包装:带卷 (TR) |
| LTC1142CG#TR | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1142CG#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1142HV | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual High Efficiency Synchronous Step-Down Switching Regulators |
| LTC1142HV-ADJ | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual High Efficiency Synchronous Step-Down Switching Regulators |
发布紧急采购，3分钟左右您将得到回复。