- 您现在的位置：买卖IC网 > PDF目录15503 > LTC1147CS8-5#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 8-SOIC PDF资料下载
参数资料
| 型号： | LTC1147CS8-5#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 6/16页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 8-SOIC |
| 标准包装： | 100 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 占空比： | 100% |
| 电源电压： | 3.5 V ~ 14 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 1332 (CN2011-ZH PDF) |
LTC1147-3.3
LTC1147-5/LTC1147L
OPERATIO
(Refer to Functional Diagram)
The LTC1147 series uses a current mode, constant off-
time architecture to switch an external P-channel power
MOSFET. Operating frequency is set by an external capaci-
tor at C T (Pin 2).
The output voltage is sensed by an internal voltage divider
connected to SENSE – (Pin 4). A voltage comparator V, and
a gain block G, compare the divided output voltage with a
reference voltage of 1.25V. To optimize efficiency, the
LTC1147 series automatically switchs between two modes
of operation, burst and continuous. The voltage compara-
tor is the primary control element when the device is in
Burst Mode operation, while the gain block controls the
output voltage in continuous mode.
During the switch “on” cycle in continuous mode, current
comparator C monitors the voltage between Pins 4 and 5
connected across an external shunt in series with the
inductor. When the voltage across the shunt reaches its
threshold value, the PDRIVE output is switched to V IN ,
turning off the P-channel MOSFET. The timing capacitor
connected to Pin 2 is now allowed to discharge at a rate
determined by the off-time controller. The discharge cur-
rent is made proportional to the output voltage (measured
by Pin 4) to model the inductor current, which decays at
a rate which is also proportional to the output voltage.
When the voltage on the timing capacitor has discharged
past V TH1 , comparator T trips, setting the flip-flop. This
causes the PDRIVE output to go low turning the P-channel
MOSFET back on. The cycle then repeats.
As the load current increases, the output voltage de-
creases slightly. This causes the output of the gain stage
APPLICATIO S I FOR ATIO
LTC1147L Adjustable Applications
When an output voltage other than 3.3V or 5V is required,
the LTC1147L adjustable version is used with an external
resistive divider from V OUT to V FB (Pin 6) (see Figure 7).
The regulated voltage is determined by:
(Pin 3) to increase the current comparator threshold, thus
tracking the load current.
The sequence of events for Burst Mode operation is very
similar to continuous operation with the cycle interrupted
by the voltage comparator. When the output voltage is at
or above the desired regulated value, the P-channel MOS-
FET is held off by comparator V and the timing capacitor
continues to discharge below V TH1 . When the timing
capacitor discharges past V TH2 , voltage comparator S
trips, causing the internal sleep line to go low.
The circuit now enters sleep mode with the power MOS-
FET turned off. In sleep mode, a majority of the circuitry is
turned off, dropping the quiescent current from 1.6mA to
160 μ A. The load current is now being supplied from the
output capacitor. When the output voltage has dropped by
the amount of hysteresis in comparator V, the P-channel
MOSFET is again turned on and this process repeats.
To avoid the operation of the current loop interfering with
Burst Mode operation, a built-in offset V OS is incorporated
in the gain stage. This prevents the current comparator
threshold from increasing until the output voltage has
dropped below a minimum threshold.
Using constant off-time architecture, the operating fre-
quency is a function of the input voltage. To minimize the
frequency variation as dropout is approached, the off-time
controller increases the discharge current as V IN drops
below V OUT + 1.5V. In dropout the P-channel MOSFET is
turned on continuously (100% duty cycle), providing low
dropout operation with V OUT ≈ V IN .
To prevent stray pickup a 100pF capacitor is suggested
across R1 located close to the LTC1147L.
For Figure 1 applications with V OUT below 2V, or when
R SENSE is moved to ground, the current sense comparator
inputs operate near ground. When the current comparator
)
V OUT = 1.25 1 +
R2
R1
)
is operated at less than 2V common mode, the off-time
increases approximately 40%, requiring the use of a
smaller timing capacitor C T .
sn1147 1147fds
6
相关PDF资料 |
PDF描述 |
|---|---|
| SPD62-103M | INDUCTOR PWR SHIELDED 10.0UH SMD |
| LTC3830-1ES8#PBF | IC REG CTRLR BUCK PWM VM 8-SOIC |
| LTC3830-1ES8 | IC REG CTRLR BUCK PWM VM 8-SOIC |
| LTC3823IGN#PBF | IC REG CTRLR BUCK PWM CM 28-SSOP |
| SPD62-682M | INDUCTOR PWR SHIELDED 6.80UH SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1147HVCS8-3.3 | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1147HVCS8-3.3#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1147HVCS8-3.3#TR | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1147HVCS8-3.3#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1147I | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Step-Down Switching Regulator Controllers |
发布紧急采购，3分钟左右您将得到回复。