- 您现在的位置：买卖IC网 > PDF目录15286 > LTC1148CS (Linear Technology)IC REG CTRLR BUCK PWM CM 14-SOIC PDF资料下载
参数资料
| 型号： | LTC1148CS |
| 厂商： | Linear Technology |
| 文件页数： | 9/20页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 14-SOIC |
| 标准包装： | 55 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 250kHz |
| 占空比： | 100% |
| 电源电压： | 3.5 V ~ 18 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
LTC1148
LTC1148-3.3/LTC1148-5
APPLICATIO S I FOR ATIO
1000
800
600
V SENSE – = V OUT = 5V
Inductor Core Selection
Once the minimum value for L is known, the type of
inductor must be selected. The highest efficiency will be
obtained using ferrite, Kool M μ ? on molypermalloy (MPP)
cores. Lower cost powdered iron cores provide suitable
400
200
V IN = 7V
V IN = 12V
V IN = 10V
performance but cut efficiency by 3% to 7%. Actual core
loss is independent of core size for a fixed inductor value,
but it is very dependent on inductance selected. As induc-
tance increases, core losses go down. Unfortunately,
0
0
100
200
300
increased inductance requires more turns of wire and
FREQUENCY (kHz)
LTC1148 ? F03
therefore copper losses increase.
Figure 3. Timing Capacitor Value
Ferrite designs have very low core loss, so design goals
can concentrate on copper loss and preventing saturation.
)
f=
where:
1
t OFF
1–
V OUT
V IN
)
Ferrite core material saturates “hard,” which means that
inductance collapses abruptly when the peak design cur-
rent is exceeded. This results in an abrupt increase in
inductor ripple current and consequent output voltage
ripple which can cause Burst Mode operation to be falsely
) )
t OFF = 1.3(10 4 )C T
V REG
V OUT
V REG is the desired output voltage (i.e., 5V, 3.3V). V OUT is
the measured output voltage. Thus V REG /V OUT = 1 in
regulation.
Note that as V IN decreases, the frequency decreases.
When the input to output voltage differential drops
below 1.5V, the LTC1148 series reduces t OFF by in-
creasing the discharge current in C T . This prevents
audible operation prior to dropout.
Once the frequency has been set by C T , the inductor L
must be chosen to provide no more than 25mV/R SENSE
of peak-to-peak inductor ripple current. This results in
a minimum required inductor value of:
L MIN = 5.1(10 5 )R SENSE (C T )V REG
As the inductor value is increased from the minimum
value, the ESR requirements for the output capacitor
are eased at the expense of efficiency. If too small an
inductor is used, the inductor current will decrease past
zero and change polarity. A consequence of this is that
the LTC1148 series may not enter Burst Mode operation
and efficiency will be severely degraded at low currents.
triggered. Do not allow the core to saturate!
Kool M μ (from Magnetics, Inc.) is a very good, low loss
core material for toroids, with a “soft” saturation charac-
teristic. Molypermalloy is slightly more efficient at high
(>200kHz) switching frequencies, but quite a bit more
expensive. Toroids are very space efficient, especially
when you can use several layers of wire. Because they
generally lack a bobbin, mounting is more difficult. How-
ever, new designs for surface mount are available from
Coiltronics and Beckman Industrial Corp. which do not
increase the height significantly.
Power MOSFET and D1 Selection
Two external power MOSFETs must be selected for use
with the LTC1148 series: a P-channel MOSFET for the
main switch, and an N-channel MOSFET for the synchro-
nous switch. The main selection criteria for the power
MOSFETs are the threshold voltage V GS(TH) and on resis-
tance R DS(ON) .
The minimum input voltage determines whether standard
threshold or logic-level threshold MOSFETs must be used.
For V IN > 8V, standard threshold MOSFETs (V GS(TH) < 4V)
may be used. If V IN is expected to drop below 8V, logic-
Kool M μ is a registered trademark of Magnetics, Inc.
114835fd
9
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B2Z-EY-F1 | CONVERTER MOD DC/DC 2V 20W |
| LTC1148CS-5 | IC REG CTRLR BUCK PWM CM 14-SOIC |
| VI-B2Z-EX-F4 | CONVERTER MOD DC/DC 2V 30W |
| LTC1148CS-3.3#PBF | IC REG CTRLR BUCK PWM CM 14-SOIC |
| VI-B2Z-EX-F3 | CONVERTER MOD DC/DC 2V 30W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1148CS#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 14-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC1148CS#TR | 功能描述:IC REG CTRLR BUCK PWM CM 14-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1148CS#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 14-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1148CS-3.3 | 功能描述:IC REG CTRLR BUCK PWM CM 14-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1148CS-3.3#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 14-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
发布紧急采购，3分钟左右您将得到回复。