- 您现在的位置：买卖IC网 > PDF目录149343 > LTC1430CS#PBF (LINEAR TECHNOLOGY CORP) Isolated Flyback Switching Regulator with 9V Output PDF资料下载
参数资料
| 型号： | LTC1430CS#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | Isolated Flyback Switching Regulator with 9V Output |
| 中文描述： | SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | 0.150 INCH, PLASTIC, SO-16 |
| 文件页数： | 11/16页 |
| 文件大小： | 211K |
| 代理商： | LTC1430CS#PBF |
4
LTC1430
G1 (Pin 1/Pin 1): Driver Output 1. Connect this pin to the
gate of the upper N-channel MOSFET, M1. This output will
swing from PVCC1 to PGND. It will always be low when G2
is high.
PVCC1 (Pin 2/Pin 2): Power VCC for Driver 1. This is the
power supply input for G1. G1 will swing from PGND to
PVCC1. PVCC1 must be connected to a potential of at least
PVCC + VGS(ON)(M1). This potential can be generated
using an external supply or a simple charge pump con-
nected to the switching node between the upper MOSFET
and the lower MOSFET; see Applications Information for
details.
PGND (Pin 3/Pin 3): Power Ground. Both drivers return to
this pin. It should be connected to a low impedance ground
in close proximity to the source of M2. 8-lead parts have
PGND and GND tied together at pin 3.
GND (Pin 4/Pin 3): Signal Ground. All low power internal
circuitry returns to this pin. To minimize regulation errors
due to ground currents, GND should be connected to
PGND right at the LTC1430. 8-lead parts have PGND and
GND tied together internally at pin 3.
SENSE –, FB, SENSE + (Pins 5, 6, 7/Pin 4): These three
pins connect to the internal resistor divider and to the
internal feedback node. To use the internal divider to set
the output voltage to 3.3V, connect SENSE + to the positive
terminal of the output capacitor and SENSE – to the nega-
tive terminal. FB should be left floating in applications that
use the internal divider. To use an external resistor divider
to set the output voltage, float SENSE + and SENSE – and
connect the external resistor divider to FB.
SHDN (Pin 8/Pin 5): Shutdown. A TTL compatible low
level at SHDN for longer than 50
s puts the LTC1430 into
shutdown mode. In shutdown, G1 and G2 go low, all
internal circuits are disabled and the quiescent current
drops to 10
A max. A TTL compatible high level at SHDN
allows the part to operate normally.
SS (Pin 9/NA): Soft-Start. The SS pin allows an external
capacitor to be connected to implement a soft-start func-
tion. An external capacitor from SS to ground controls the
start-up time and also compensates the current limit loop,
allowing the LTC1430 to enter and exit current limit
cleanly. See Applications Information for more details.
COMP (Pin 10/Pin 6): External Compensation. The COMP
pin is connected directly to the output of the error amplifier
and the input of the PWM. An RC network is used at this
node to compensate the feedback loop to provide opti-
mum transient response. See Applications Information for
compensation details.
FREQSET (Pin 11/NA): Frequency Set. This pin is used to
set the free running frequency of the internal oscillator.
With the pin floating, the oscillator runs at about 200kHz.
A resistor from FREQSET to ground will speed up the
oscillator; a resistor to VCC will slow it down. See Applica-
tions Information for resistor selection details.
IMAX (Pin 12/NA): Current Limit Set. IMAX sets the thresh-
old for the internal current limit comparator. If IFB drops
below IMAX with G1 on, the LTC1430 will go into current
limit. IMAX has a 12A pull-down to GND. It can be adjusted
with an external resistor to PVCC or an external voltage
source.
IFB (Pin 13/NA): Current Limit Sense. Connect to the
switched node at the source of M1 and the drain of M2
through a 1k resistor. The 1k resistor is required to prevent
voltage transients from damaging IFB. This pin can be
taken up to 18V above GND without damage.
VCC (Pin 14/Pin 7): Power Supply. All low power internal
circuits draw their supply from this pin. Connect to a clean
power supply, separate from the main PVCC supply at the
drain of M1. This pin requires a 4.7
F bypass capacitor.
8-lead parts have VCC and PVCC2 tied together at pin 7 and
require a 10
F bypass to GND.
PVCC2 (Pin 15/Pin 7): Power VCC for Driver 2. This is the
power supply input for G2. G2 will swing from GND to
PVCC2. PVCC2 is usually connected to the main high power
supply. The 8-lead parts have VCC and PVCC2 tied together
at pin 7 and require a 10
F bypass to GND.
G2 (Pin 16/Pin 8): Driver Output 2. Connect this pin to the
gate of the lower N-channel MOSFET, M2. This output will
swing from PVCC2 to PGND. It will always be low when G1
is high.
(16-Lead Package/8-Lead Package)
PI FU CTIO S
UU
U
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1430IS#PBF | Isolated Flyback Switching Regulator with 9V Output |
| LTC1430IS#TRPBF | Isolated Flyback Switching Regulator with 9V Output |
| LTC1435AIG#TRPBF | High Efficiency Low Noise Synchronous Step-Down Switching Regulator |
| LTC1435AIS#TRPBF | High Efficiency Low Noise Synchronous Step-Down Switching Regulator |
| LTC1436ACGN#PBF | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1430CSTR | 制造商:LT 功能描述:* |
| LTC1430IS | 功能描述:IC SW REG CNTRLR STEP-DWN 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC1430IS#PBF | 功能描述:IC SW REG CNTRLR STEP-DWN 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC1430IS#TR | 功能描述:IC SW REG CNTRLR STEP-DWN 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC1430IS#TRPBF | 功能描述:IC SW REG CNTRLR STEP-DWN 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。