- 您现在的位置：买卖IC网 > PDF目录13061 > LTC1430CS#TR (Linear Technology)IC SW REG CNTRLR STEP-DWN 16SOIC PDF资料下载
参数资料
| 型号： | LTC1430CS#TR |
| 厂商： | Linear Technology |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | IC SW REG CNTRLR STEP-DWN 16SOIC |
| 标准包装： | 2,500 |
| 应用： | 控制器，Intel Pentium? |
| 输入电压： | 4 V ~ 8 V |
| 输出数： | 1 |
| 输出电压： | 3.3V，可调 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
LTC1430
APPLICATIO S I FOR ATIO
Once the threshold voltage has been selected, R ON should
be chosen based on input and output voltage, allowable
power dissipation and maximum required output current.
In a typical LTC1430 buck converter circuit operating in
continuous mode, the average inductor current is equal to
the output load current. This current is always flowing
through either M1 or M2 with the power dissipation split
up according to the duty cycle:
Note that the required R ON for M2 is roughly twice that of
M1 in this example. This application might specify a single
0.03 ? device for M2 and parallel two more of the same
devices to form M1. Note also that while the required R ON
values suggest large MOSFETs, the dissipation numbers
are only 1.1W per device or less—large TO-220 packages
and heat sinks are not necessarily required in high effi-
ciency applications. Siliconix Si4410DY (in SO-8) and
DC ( M 1 ) =
V OUT
V IN
Motorola MTD20N03HL (in DPAK) are two small, surface
mount devices with R ON values of 0.03 ? or below with 5V
of gate drive; both work well in LTC1430 circuits with up
DC ( M 2 ) = 1 ? OUT
( V IN ? V OUT )
V
V IN
=
V IN
The R ON required for a given conduction loss can now be
calculated by rearranging the relation P = I 2 R:
to 10A output current. A higher P MAX value will generally
decrease MOSFET cost and circuit efficiency and increase
MOSFET heat sink requirements.
Inductor
The inductor is often the largest component in an LTC1430
design and should be chosen carefully. Inductor value and
type should be chosen based on output slew rate require-
R ON ( M 1 ) =
=
P MAX ( M 1 )
)
DC ( M 1 ) ? I MAX 2
V IN ? P MAX ( M 1
V OUT ? I MAX 2
ments and expected peak current. Inductor value is prima-
rily controlled by the required current slew rate. The
maximum rate of rise of the current in the inductor is set
by its value, the input-to-output voltage differential and the
maximum duty cycle of the LTC1430. In a typical 5V to
3.3V application, the maximum rise time will be:
R ON ( M 2 ) =
V IN ? P MAX ( M 2 )
( V IN ? V OUT ) ? I MAX 2
( V IN ? V OUT ) AMPS 1 . 53 A I
μ s L
P MAX ( M 2 )
DC ( M 2 ) ? I MAX 2
=
P MAX should be calculated based primarily on required
efficiency. A typical high efficiency circuit designed for 5V
in, 3.3V at 10A out might require no more than 3%
efficiency loss at full load for each MOSFET. Assuming
roughly 90% efficiency at this current level, this gives a
P MAX value of (3.3V ? 10A/0.9) ? 0.03 = 1.1W per FET and
a required R ON of:
90 % ? =
L SECOND
where L is the inductor value in μ H. A 2 μ H inductor would
have a 0.76A/ μ s rise time in this application, resulting in a
6.5 μ s delay in responding to a 5A load current step. During
this 6.5 μ s, the difference between the inductor current and
the output current must be made up by the output capaci-
tor, causing a temporary droop at the output. To minimize
this effect, the inductor value should usually be in the 1 μ H
to 5 μ H range for most typical 5V to 3.xV LTC1430 circuits.
Different combinations of input and output voltages and
expected loads may require different values.
= 0 . 017 ?
= 0 . 032 ?
R ON ( M 1 ) =
R ON ( M 2 ) =
8
5 V ? 1 . 1 W
3 . 3 V ? 10 A 2
5 V ? 1 . 1 W
( 5 V ? 3 . 3 V ) ? 10 A 2
Once the required value is known, the inductor core type
can be chosen based on peak current and efficiency
requirements. Peak current in the inductor will be equal to
the maximum output load current added to half the peak-
to- peak inductor ripple current. Ripple current is set by the
相关PDF资料 |
PDF描述 |
|---|---|
| MIC37300-3.3WR | IC REG LDO 3.3V 3A S-PAK-3 |
| GMA15DTAS | CONN EDGECARD 30POS R/A .125 SLD |
| LTC1736CG#TR | IC REG SW SYNC STEPDWN HE 24SSOP |
| EGM43DTKT-S288 | CONN EDGECARD 86POS .156 EXTEND |
| LTC3876EFE#TRPBF | IC CTLR DC/DC DDR DUAL 38-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1430IS | 功能描述:IC SW REG CNTRLR STEP-DWN 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC1430IS#PBF | 功能描述:IC SW REG CNTRLR STEP-DWN 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC1430IS#TR | 功能描述:IC SW REG CNTRLR STEP-DWN 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC1430IS#TRPBF | 功能描述:IC SW REG CNTRLR STEP-DWN 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC1433CGN | 功能描述:IC REG BUCK 3.3V/5V/ADJ 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。