- 您现在的位置：买卖IC网 > PDF目录17165 > LTC1559CGN-5#TRPBF (Linear Technology)IC BACKUP BATT CNTRLR 5V 16-SSOP PDF资料下载
参数资料
| 型号： | LTC1559CGN-5#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 5/20页 |
| 文件大小： | 0K |
| 描述： | IC BACKUP BATT CNTRLR 5V 16-SSOP |
| 标准包装： | 2,500 |
| 功能： | 备份管理 |
| 电池化学： | 镍镉 |
| 电源电压： | 4.4 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 带卷 (TR) |
LTC1559-3.3/LTC1559-5
PI N FU N CTIO N S
Pin Numbers Are Shown First for the SO-8 Package
Then the GN16 and S16 Packages
SW (Pins 1/1, 2): Boost Converter Switching Node. Con-
nect a 22 μ H inductor from SW to the positive terminal of
the backup cell. In backup mode, this node is alternately
switched between ground and V BAK , generating the backup
output voltage. In fast or trickle charge mode, an internal
regulator outputs a constant DC current from this pin
through the 22 μ H inductor and into the NiCd battery.
During power-up or undervoltage lockout (UVLO), the SW
pin enters a high impedance state.
GND (Pins 2/4): System Ground. The low power internal
circuitry returns to this pin in the 16-pin packages. GND
and PGND are bonded together to this pin in the 8-pin
package.
CTL (Pins 3/5): Control. This pin provides three functions.
In backup mode this pin is a high impedance input and
monitors the backup battery cell voltage (V BAT ). If V BAT
drops below 0.9V, the LTC1559 enters UVLO. During
trickle charge mode, an external resistor R EXT sets the
trickle charge current. In all modes, pulling the CTL pin
below 250mV generates either a “soft” or “hard” reset
pulse. See the Applications Information section for more
information.
PS (Pins 4/7): Power Supply Sense. This pin senses the
presence of the main supply and triggers the LTC1559 to
terminate backup mode. During backup, V CC is driven
externally by the LTC1559’s boost convert’s output (V BAK ).
When PS > V CC during backup, the LTC1559 pulls down
the BACKUP pin, reconnecting the system regulator out-
put to the system V CC . The PS pin is needed in applications
that use a P-channel MOSFET (driven by the BACKUP
signal) to isolate the system regulator during backup. If
not needed, PS can be disabled by tying it to ground.
RESET (Pins 5/11): System Reset, Active Low. This is an
open-drain output. This pin provides a low going reset
signal to the system processor. A 200ms pulse is gener-
ated if the CTL pin is pulled low for more than two seconds
(“hard” reset) or if the LTC1559 comes out of UVLO. This
“hard reset” stops the internal boost converter if it is
running. This pin is held low if the LTC1559 is in UVLO and
is guaranteed to be valid when V CC is greater than or equal
to 1V.
RESET also provides a low going 100 μ s signal whenever
the CTL pin is pulled low for less than two seconds (“soft”
reset). Unlike hard reset, soft reset does not affect the
LTC1559’s current operating mode.
BACKUP (Pins 6/13): System Backup Signal. This is a
TTL-compatible output driver that pulls low unless the
LTC1559 is in backup mode. BACKUP signals the system
controller that the system is in backup mode so that it can
reduce system loading. BACKUP can also be used to drive
the gate of a P-channel MOSFET in series with the main
system regulator’s output. See the Applications Informa-
tion section for more details.
V CC (Pins 7/14): Power Supply Input. All internal circuits
except the boost converter are powered from this pin. A
0.1 μ F bypass capacitor is required from V CC to ground.
The UVLO detector inside the LTC1559 monitors V CC . If
V CC drops below the rated output voltage by 9%, the
LTC1559 enters UVLO mode and RESET is asserted. The
LTC1559-3.3 exits UVLO if V CC rises to greater than
– 5.5% of the rated output voltage. The LTC1559-5 exits
UVLO if V CC rises to greater than –6 % of the rated output
voltage. See the Applications Information section for more
details.
V BAK (Pins 8/15,16): Backup Supply Output. The LTC1559’s
boost converter provides the regulated output voltage to
the system through V BAK during backup mode.
16-Pin GN and SO Packages
PGND (Pin 3): Power Ground. The internal driver circuitry
returns to this pin. PGND should be connected to a low
impedance ground plane in close proximity to the NiCd
battery cell.
SHDN (Pin 6): Chip Shutdown. A TTL-compatible active
low voltage at SHDN puts the LTC1559 into low power
shutdown mode. In shutdown, all internal circuits power
down and are held in a reset state. The SW, CTL and V BAK
pins enter into high impedance states. In shutdown mode,
supply current drops to below 50 μ A and current drawn
from the backup cell drops to below 15 μ A.
5
相关PDF资料 |
PDF描述 |
|---|---|
| V375C15C75BF2 | CONVERTER MOD DC/DC 15V 75W |
| 12RS473C | INDUCT RAD 47UH 2.2A T/H 10X10 |
| HSC08DRYN-S13 | CONN EDGECARD 16POS .100 EXTEND |
| 12RS683C | INDUCT RAD 68UH 1.8A T/H 10X10 |
| V375C15C75BL3 | CONVERTER MOD DC/DC 15V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1559CS-3.3 | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1559CS-3.3#PBF | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LTC1559CS-3.3#TRPBF | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LTC1559CS-5 | 功能描述:IC BACKUP BATT CNTRLR 5V 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1559CS-5#PBF | 功能描述:IC BACKUP BATT CNTRLR 5V 16-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
发布紧急采购，3分钟左右您将得到回复。