- 您现在的位置：买卖IC网 > PDF目录14136 > LTC1627CS8#TR (Linear Technology)IC REG BUCK SYNC ADJ 0.5A 8SOIC PDF资料下载
参数资料
| 型号： | LTC1627CS8#TR |
| 厂商： | Linear Technology |
| 文件页数： | 9/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 0.5A 8SOIC |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 8.5 V |
| 输入电压： | 2.65 V ~ 8.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 35kHz ~ 350kHz |
| 电流 - 输出： | 500mA |
| 同步整流器： | 是 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-SOIC |
LTC1627
APPLICATIO S I FOR ATIO
The selection of C OUT is driven by the required effective series
resistance (ESR). Typically, once the ESR requirement is
0.8V ≤ V OUT ≤ 8.5V
? V OUT ? ? I L ? ESR + ?
satisfied,thecapacitanceisadequateforfiltering.Theoutput
ripple ? V OUT is determined by:
? 1 ?
? 8 fC OUT ?
V FB
LTC1627
GND
R2
R1
1627 F04
where f = operating frequency, C OUT = output capacitance
and ? I L = ripple current in the inductor. The output ripple
is highest at maximum input voltage since ? I L increases
with input voltage. For the LTC1627, the general rule for
proper operation is:
C OUT required ESR < 0.25 ?
Manufacturers such as Nichicon, United Chemicon and
Sanyo should be considered for high performance through-
hole capacitors. The OS-CON semiconductor dielectric
capacitor available from Sanyo has the lowest ESR/size
ratio of any aluminum electrolytic at a somewhat higher
price. Once the ESR requirement for C OUT has been met,
the RMS current rating generally far exceeds the
I RIPPLE(P-P) requirement.
In surface mount applications multiple capacitors may
have to be paralleled to meet the ESR or RMS current
handling requirements of the application. Aluminum elec-
trolytic and dry tantalum capacitors are both available in
surface mount configurations. In the case of tantalum, it is
Figure 4. Setting the LTC1627 Output Voltage
Run/Soft-Start Function
The RUN/SS pin is a dual purpose pin that provides the
soft-start function and a means to shut down the LTC1627.
Soft-start reduces surge currents from V IN by gradually
increasing the internal current limit. Power supply
sequencing can also be accomplished using this pin.
An internal 2.25 μ A current source charges up an external
capacitor C SS . When the voltage on RUN/SS reaches 0.7V
the LTC1627 begins operating. As the voltage on RUN/SS
continues to ramp from 0.7V to 1.8V, the internal current
limit is also ramped at a proportional linear rate. The
current limit begins at 25mA (at V RUN/SS ≤ 0.7V) and ends
at the Figure 3 value (V RUN/SS ≈ 1.8V). The output current
thus ramps up slowly, charging the output capacitor. If
RUN/SS has been pulled all the way to ground, there will
be a delay before the current starts increasing and is given
by:
critical that the capacitors are surge tested for use in
switching power supplies. An excellent choice is the AVX
TPS series of surface mount tantalum, available in case
t DELAY =
0 . 7C SS
2 . 25 μ A
heights ranging from 2mm to 4mm. Other capacitor types
include Sanyo POSCAP, KEMET T510 and T495 series,
Nichicon PL series and Sprague 593D and 595D series.
Consult the manufacturer for other specific recommenda-
tions.
Output Voltage Programming
Pulling the RUN/SS pin below 0.4V puts the LTC1627 into
a low quiescent current shutdown (I Q < 15 μ A). This pin can
be driven directly from logic as shown in Figure 5. Diode
D1 in Figure 5 reduces the start delay but allows C SS to
ramp up slowly providing the soft-start function. This
diode can be deleted if soft-start is not needed.
The output voltage is set by a resistive divider according
to the following formula:
3.3V OR 5V
D1
RUN/SS
RUN/SS
V OUT = 0 . 8 V ? 1 +
?
?
R 2 ?
R 1 ? ?
(2)
C SS
C SS
1627 F05
The external resistive divider is connected to the output,
Figure 5. RUN/SS Pin Interfacing
allowing remote voltage sensing as shown in Figure 4.
9
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1503IS8-2#TRPBF | IC REG BUCK SWITCHD CAP 2V 8SOIC |
| LTC1503IS8-2#TR | IC REG BUCK SWITCHD CAP 2V 8SOIC |
| LTC1503IS8-1.8#TR | IC REG BUCK SWITCHED CAP 8SOIC |
| HSM18DRXI | CONN EDGECARD 36POS DIP .156 SLD |
| HMM18DRXI | CONN EDGECARD 36POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1627IS8 | 功能描述:IC REG BUCK SYNC ADJ 0.5A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC1627IS8#PBF | 功能描述:IC REG BUCK SYNC ADJ 0.5A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC1627IS8#TR | 功能描述:IC REG BUCK SYNC ADJ 0.5A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC1627IS8#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 0.5A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC1628CG | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
发布紧急采购，3分钟左右您将得到回复。