- 您现在的位置：买卖IC网 > PDF目录44988 > LTC1628IG#PBF (LINEAR TECHNOLOGY CORP) 3 A SWITCHING CONTROLLER, 310 kHz SWITCHING FREQ-MAX, PDSO28 PDF资料下载
参数资料
| 型号： | LTC1628IG#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 3 A SWITCHING CONTROLLER, 310 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封装： | 0.209 INCH, PLASTIC, SSOP-28 |
| 文件页数： | 5/32页 |
| 文件大小： | 360K |
| 代理商： | LTC1628IG#PBF |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
13
LTC1628/LTC1628-PG
the RMS input current varies for single-phase and 2-phase
operation for 3.3V and 5V regulators over a wide input
voltage range.
It can readily be seen that the advantages of 2-phase
operation are not just limited to a narrow operating range,
but in fact extend over a wide region. A good rule of thumb
for most applications is that 2-phase operation will reduce
Figure 4. RMS Input Current Comparison
Figure 1 on the first page is a basic LTC1628 application
circuit. External component selection is driven by the
load requirement, and begins with the selection of RSENSE
and the inductor value. Next, the power MOSFETs and D1
are selected. Finally, CIN and COUT are selected. The
circuit shown in Figure 1 can be configured for operation
up to an input voltage of 28V (limited by the external
MOSFETs).
RSENSE Selection For Output Current
RSENSE is chosen based on the required output current.
The LTC1628 current comparator has a maximum thresh-
old of 75mV/RSENSE and an input common mode range of
SGND to 1.1(INTVCC). The current comparator threshold
sets the peak of the inductor current, yielding a maximum
average output current IMAX equal to the peak value less
half the peak-to-peak ripple current,
IL.
Allowing a margin for variations in the LTC1628 and
external component values yields:
R
mV
I
SENSE
MAX
=
50
When using the controller in very low dropout conditions,
the maximum output current level will be reduced due to
the internal compensation required to meet stability crite-
rion for buck regulators operating at greater than 50%
duty factor. A curve is provided to estimate this reducton
in peak output current level depending upon the operating
duty factor.
Selection of Operating Frequency
The LTC1628 uses a constant frequency architecture with
the frequency determined by an internal oscillator capaci-
tor. This internal capacitor is charged by a fixed current
plus an additional current that is proportional to the
voltage applied to the FREQSET pin.
A graph for the voltage applied to the FREQSET pin vs
frequency is given in Figure 5. As the operating frequency
INPUT VOLTAGE (V)
0
INPUT
RMS
CURRENT
(A)
3.0
2.5
2.0
1.5
1.0
0.5
0
10
20
30
40
1628 F04
SINGLE PHASE
DUAL CONTROLLER
2-PHASE
DUAL CONTROLLER
VO1 = 5V/3A
VO2 = 3.3V/3A
the input capacitor requirement to that for just one channel
operating at maximum current and 50% duty cycle.
A final question: If 2-phase operation offers such an
advantage over single-phase operation for dual switching
regulators, why hasn’t it been done before? The answer is
that, while simple in concept, it is hard to implement.
Constant-frequency current mode switching regulators
require an oscillator derived “slope compensation” signal
to allow stable operation of each regulator at over 50%
duty cycle. This signal is relatively easy to derive in single-
phase dual switching regulators, but required the develop-
ment of a new and proprietary technique to allow 2-phase
operation. In addition, isolation between the two channels
becomes more critical with 2-phase operation because
switch transitions in one channel could potentially disrupt
the operation of the other channel.
The LTC1628 is proof that these hurdles have been sur-
mounted. The new device offers unique advantages for the
ever-expanding number of high efficiency power supplies
required in portable electronics.
(Refer to Functional Diagram)
OPERATIO
U
APPLICATIO S I FOR ATIO
WU
UU
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1628IG-SYNC#TR | 3 A SWITCHING CONTROLLER, 360 kHz SWITCHING FREQ-MAX, PDSO28 |
| LTC1643HCGN#PBF | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC1643LCGN#TR | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC1728HS5-5 | 3-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| LTC1729CS8-8.4#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1628IG-PG | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1628IG-PG#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1628IG-PG#TR | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1628IG-PG#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1628IGSYNC | 制造商:Linear Technology 功能描述: |
发布紧急采购，3分钟左右您将得到回复。