- 您现在的位置：买卖IC网 > PDF目录15257 > LTC1628IG-PG (Linear Technology)IC REG CTRLR BUCK PWM CM 28-SSOP PDF资料下载
参数资料
| 型号： | LTC1628IG-PG |
| 厂商： | Linear Technology |
| 文件页数： | 22/32页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 28-SSOP |
| 标准包装： | 47 |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 360kHz |
| 占空比： | 99.4% |
| 电源电压： | 3.5 V ~ 30 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC1628/LTC1628-PG
APPLICATIO S I FOR ATIO
FCB Pin Operation
The FCB pin can be used to regulate a secondary winding
or as a logic level input. Continuous operation is forced
when the FCB pin drops below 0.8V. During continuous
internal current source pulling the pin high. Include this
current when choosing resistor values R5 and R6.
The following table summarizes the possible states avail-
able on the FCB pin:
mode, current flows continuously in the transformer pri-
mary. The secondary winding(s) draw current only when
the bottom, synchronous switch is on. When primary load
currents are low and/or the V IN /V OUT ratio is low, the
synchronous switch may not be on for a sufficient amount
of time to transfer power from the output capacitor to the
secondary load. Forced continuous operation will support
secondary windings providing there is sufficient synchro-
nous switch duty factor. Thus, the FCB input pin removes
Table 1
FCB Pin
0V to 0.75V
0.85V < V FCB < 4.3V
Feedback Resistors
>4.8V
Condition
Forced Continuous (Current Reversal
Allowed—Burst Inhibited)
Minimum Peak Current Induces
Burst Mode Operation
No Current Reversal Allowed
Regulating a Secondary Winding
Burst Mode Operation Disabled
the requirement that power must be drawn from the
inductor primary in order to extract power from the
auxiliary windings. With the loop in continuous mode, the
auxiliary outputs may nominally be loaded without regard
to the primary output load.
The secondary output voltage V SEC is normally set as
shown in Figure 6a by the turns ratio N of the transformer:
V SEC ? (N + 1) V OUT
However, if the controller goes into Burst Mode operation
and halts switching due to a light primary load current,
then V SEC will droop. An external resistive divider from
V SEC to the FCB pin sets a minimum voltage V SEC(MIN) :
Constant Frequency Mode Enabled
No Current Reversal Allowed
No Minimum Peak Current
The FLTCPL pin determines whether only the first or both
controllers are temporarily forced into continuous mode
when the FCB pin falls below 0.8V. Tying the FLTCPL pin
to ground will send only the first controller into continuous
operation while tying the FLTCPL pin to INTV CC will send
both controllers into continuous operation.
Voltage Positioning
Voltage positioning can be used to minimize peak-to-peak
output voltage excursions under worst-case transient
loading conditions. The open-loop DC gain of the control
V SEC ( MIN ) ≈ 0 . 8 V ? 1 +
R 5 ?
?
?
R 6 ?
?
loop is reduced depending upon the maximum load step
specifications. Voltage positioning can easily be added to
the LTC1628 by loading the I TH pin with a resistive divider
If V SEC drops below this level, the FCB voltage forces
temporary continuous switching operation until V SEC is
again above its minimum.
In order to prevent erratic operation if no external connec-
tions are made to the FCB pin, the FCB pin has a 0.18 μ A
having a Thevenin equivalent voltage source equal to the
midpoint operating voltage of the error amplifier, or 1.2V
(see Figure 8).
The resistive load reduces the DC loop gain while main-
taining the linear control range of the error amplifier. The
maximum output voltage deviation can theoretically be
INTV CC
R T2
I TH
R T1
R C
LTC1628
C C
1628 F08
Figure 8. Active Voltage Positioning Applied to the LTC1628
1628fb
22
相关PDF资料 |
PDF描述 |
|---|---|
| VE-27Y-EY-F1 | CONVERTER MOD DC/DC 3.3V 33W |
| RCA36DRMH | CONN EDGECARD 72POS .125 SQ WW |
| LTC3805MPMSE#TRPBF | IC REG CTRLR BST FLYBK CM 10MSOP |
| NCP302LSN47T1G | IC VOLT DETECT CMOS 4.7V 5TSOP |
| LTC1266AIS#TRPBF | IC REG CTRLR BST PWM CM 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1628IG-PG#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1628IG-PG#TR | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1628IG-PG#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1628IGSYNC | 制造商:Linear Technology 功能描述: |
| LTC1628IG-SYNC | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
发布紧急采购，3分钟左右您将得到回复。