- 您现在的位置：买卖IC网 > PDF目录15327 > LTC1700EMS#TRPBF (Linear Technology)IC REG CTRLR BST PWM CM 10-MSOP PDF资料下载
参数资料
| 型号： | LTC1700EMS#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM CM 10-MSOP |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 680kHz |
| 占空比： | 92% |
| 电源电压： | 0.9 V ~ 6 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
LTC1700
APPLICATIO N S I N FOR M ATIO N
L MIN ≥ V IN ( MAX ) ? ?
To eliminate this subharmonic oscillation, a compensat-
ing ramp is added internally to the LTC1700 on the
inductor current waveform when the duty cycle exceeds
5%. This scheme, known as slope compensation, makes
the loop perceive that there is more inductor current than
it actually has. As a result, the maximum current capability
of the regulator is reduced. This reduction is proportional
to the duty cycle and is shown in Figure 5. Hence for
applications that operate at high duty cycles, the
N-channel MOSFET chosen should have a lower R DS(ON)
to make up for this reduction (See Design Example).
1.2
? DC ?
? f ? I L ?
With Burst Mode operation enabled on the LTC1700, the
ripple current is normally set such that the inductor
current is continuous during burst periods. Remember
that during bursting, the peak current is clamped at
approximately:
I BURST(PEAK) ? 36mV/R DS(ON)
Hence the peak-to-peak ripple selected for optimal burst
mode operation should not exceed I BURST(PEAK) . This
implies a minimum inductance of:
( f )( 0 . 66 ) ? ?
1.0
0.8
0.6
L MINBURST =
V IN ( MAX ) ( DC )
? I OMAX ?
? 1 – DC ?
0.4
0.2
In applications that invoke Burst Mode operation, the
inductor should be chosen so it has low ripple (0.4I OMAX )
current during heavy load and continuous operation dur-
0
0
10
20
30 40 50
DUTY CYCLE (%)
60
70
ing bursting. The criteria for selecting which equation to
use is:
? I L = V IN ?
? fL ?
1700 F05
Figure 5. Maximum Output Current vs Duty Cycle
Inductor Value Selection
Given the input voltage, inductor value and operating
frequency, the ripple current can be calculated:
? DC ?
?
Lower ripple current reduces core losses in the inductor,
ESR losses in the output capacitors and output voltage
ripple. Thus, highest efficiency operation is obtained at
low frequency with small ripple current. To achieve this,
however, requires a larger inductor.
A reasonable starting point is to choose a ripple current
that is about 40% of I O(MAX) . Note that the largest ripple
current occurs at the highest V IN . To guarantee that ripple
current does not exceed a specified maximum, the induc-
tor should be chosen according to:
Use L MIN for Duty Cycle > 36%
Use L MINBURST for Duty Cycle ≤ 36%
A smaller value than L MIN could be used in the circuit;
however, the inductor current will not be continuous
during burst periods. The advantage of using a smaller
inductance than L MIN is primarily size. The disadvantage is
higher output ripple.
Inductor Core Selection
Once the value for L is known, the type of inductor must be
selected. High efficiency converters generally cannot af-
ford the core loss found in low cost powdered iron cores,
forcing the use of more expensive ferrite, molypermalloy,
or Kool M μ ? cores. Actual core loss is independent of core
size for a fixed inductor value, but it is very dependent on
inductance selected. As inductance increases, core losses
go down. Unfortunately, increased inductance requires
more turns of wire and therefore copper losses will
increase. Ferrite designs have very low core losses and are
Kool M μ is a registered trademark of Magnetics, Inc.
1700fa
10
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3852IUDD#PBF | IC REG CTRLR DOUBLER PWM 24-QFN |
| VI-JWT-EY-F2 | CONVERTER MOD DC/DC 6.5V 50W |
| ADM802MARN | IC SUPERVISOR MPU 4.40V WD 8SOIC |
| IMC1210BN180J | INDUCTOR WW 18UH 5% 1210 |
| LTC3808EGN#PBF | IC REG CTRLR BUCK PWM CM 16-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1701BES5 | 制造商:Linear Technology 功能描述:1.1 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO5 |
| LTC1701BES5#PBF | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 2.5V to 5.5V 5-Pin TSOT-23 制造商:Linear Technology 功能描述:DP-SWREG/Monolithic, CUT TAPE 1MHz Step-dn DC/DC Con in SOT-23 |
| LTC1701BES5#TR | 功能描述:IC REG BUCK ADJ 0.5A TSOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC1701BES5#TRM | 功能描述:IC REG BUCK ADJ 0.5A TSOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC1701BES5#TRMPBF | 功能描述:IC REG BUCK ADJ 0.5A TSOT23-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。