- 您现在的位置：买卖IC网 > PDF目录15327 > LTC1700EMS#TRPBF (Linear Technology)IC REG CTRLR BST PWM CM 10-MSOP PDF资料下载
参数资料
| 型号： | LTC1700EMS#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM CM 10-MSOP |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 680kHz |
| 占空比： | 92% |
| 电源电压： | 0.9 V ~ 6 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
LTC1700
APPLICATIO N S I N FOR M ATIO N
preferred at high switching frequencies, so design goals
can concentrate on copper loss and preventing saturation.
Ferrite core material saturates “hard”, which means that
inductance collapses abruptly when the peak design cur-
rent is exceeded. This results in an abrupt increase in
inductor ripple current and output voltage ripple. Do not
allow the core to saturate!
Molypermalloy (from Magnetics, Inc.) is a very good, low
loss core material for toroids, but it is more expensive than
ferrite. A reasonable compromise from the same manu-
facturer is Kool M μ . Toroids are very space efficient,
especially when you can use several layers of wire. Be-
cause they generally lack a bobbin, mounting is more
difficult. However, new designs for surface mount are
available which do not increase the height significantly.
C OUT Selection
During continuous operation, the output capacitor has a
trapezoidal current profile. The RMS current into the
capacitor is then given by:
dependent term but can be compensated for by using
capacitors of very low ESR to maintain low ripple voltage.
The I TH pin OPTI-LOOP compensation components can be
optimized to provide stable, high performance transient
response regardless of the output capacitors selected.
Manufacturers such as Nichicon, United Chemicon and
Sanyo should be considered for high performance through-
hole capacitors. The OS-CON semiconductor dielectric
capacitor available from Sanyo has the lowest ESR (size)
product of any aluminum electrolytic at a somewhat
higher price.
Multiple capacitors may have to be paralleled to meet the
ESR or RMS current handling requirements of the applica-
tion. Aluminum electrolytic and dry tantalum capacitors
are both available in surface mount configurations. In the
case of tantalum, it is critical that the capacitors are surge
tested for use in switching power supplies. An excellent
choice is the AVX TPS series of surface mount tantalum,
available in case heights ranging from 2mm to 4mm. Other
capacitor types include Sanyo OS-CON, Nichicon PL se-
ries and Sprague 593D and 595D series. Consult the
I COUT ( RMS ) ? ? I OUT
– 1 ?
?
?
V OUT
V IN
?
?
manufacturer for other specific recommendations.
Setting Output Voltage
The RMS current is greatest at I OUT(MAX) and minimum
input working voltage. Therefore the output capacitor
should be chosen with a rating at least I COUT(RMS) . Several
capacitors can also be paralleled to meet this requirement.
Besides RMS current rating, the selection of C OUT is also
driven by the required effective series resistance (ESR).
The ESR of the capacitor together with its capacitance
determines the output ripple voltage and can be expressed
as:
The LTC1700 develops a 1.205V reference voltage be-
tween the feedback (Pin 3) terminal and ground (see
Figure 6). By selecting resistor R1, a constant current is
caused to flow through R1 and R2 to set the overall output
voltage. The regulated output voltage is determined by:
V OUT = 1.205(1 + R2/R1)
For most applications, a 30k resistor is suggested for R1.
To prevent stray pickup, a 100pF capacitor is suggested
? V OUT ≈ I PK ( ESR ) +
2 I OUT
C OUT
t ON
across R1 located close to LTC1700.
Efficiency Considerations
where C OUT = output capacitance, t ON = on time of main
V OUT
MOSFET and I PK = peak inductor current. A common
technique to lower the total ESR at the output is to parallel
the output capacitor with a 10 μ F ceramic capacitor.
The choice of using a smaller output capacitance in-
creases the output ripple voltage due to the frequency
LTC1700
V FB
R2
R1
1700 ? F06
Figure 6. Setting Output Voltage
1700fa
11
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3852IUDD#PBF | IC REG CTRLR DOUBLER PWM 24-QFN |
| VI-JWT-EY-F2 | CONVERTER MOD DC/DC 6.5V 50W |
| ADM802MARN | IC SUPERVISOR MPU 4.40V WD 8SOIC |
| IMC1210BN180J | INDUCTOR WW 18UH 5% 1210 |
| LTC3808EGN#PBF | IC REG CTRLR BUCK PWM CM 16-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1701BES5 | 制造商:Linear Technology 功能描述:1.1 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO5 |
| LTC1701BES5#PBF | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 2.5V to 5.5V 5-Pin TSOT-23 制造商:Linear Technology 功能描述:DP-SWREG/Monolithic, CUT TAPE 1MHz Step-dn DC/DC Con in SOT-23 |
| LTC1701BES5#TR | 功能描述:IC REG BUCK ADJ 0.5A TSOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC1701BES5#TRM | 功能描述:IC REG BUCK ADJ 0.5A TSOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC1701BES5#TRMPBF | 功能描述:IC REG BUCK ADJ 0.5A TSOT23-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。