- 您现在的位置：买卖IC网 > PDF目录15266 > LTC1702IGN (Linear Technology)IC REG CTRLR BUCK PWM VM 24-SSOP PDF资料下载
参数资料
| 型号： | LTC1702IGN |
| 厂商： | Linear Technology |
| 文件页数： | 18/36页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 24-SSOP |
| 标准包装： | 55 |
| 系列： | PolyPhase® |
| PWM 型： | 电压模式 |
| 输出数： | 2 |
| 频率 - 最大： | 750kHz |
| 占空比： | 93% |
| 电源电压： | 3 V ~ 7 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC1702
APPLICATIO N S I N FOR M ATIO N
bypass capacitor gets exercised in three ways: its ESR
must be low enough to keep the initial drop as QT turns on
within reason (100mV or so); its RMS current capability
must be adequate to withstand the 4.6A RMS ripple current
at the input and the capacitance must be large enough to
maintain the input voltage until the input supply can make
up the difference. Generally, a capacitor that meets the
firsttwoparameterswillhavefarmorecapacitancethanis
required to keep capacitance-based droop under control.
In our example, we need 0.01 ? ESR to keep the input drop
under 100mV with a 10A current step and 4.6A RMS ripple
current capacity to avoid overheating the capacitor. These
requirements can be met with multiple low ESR tantalum
or electrolytic capacitors in parallel, or with a large mono-
lithic ceramic capacitor.
The two sides of the LTC1702 run off a single master clock
and are wired 180 ° out of phase with each other to
significantly reduce the total capacitance/ESR needed at
the input. Assuming 100mV of ripple and 10A output
current, we needed an ESR of 0.01 ? and 4.7A ripple
current capability for one side. Now, assume both sides
are running simultaneously with identical loading. If the
two sides switched in phase, all the loading conditions
would double and we’d need enough capacitance for
9.4A RMS and 0.005 ? ESR. With the two sides out of
phase, the input current is 4.8A RMS —barely larger than
Calculating RMS Current in C IN
A buck regulator like the LTC1702 draws pulses of
current from the input capacitor during normal opera-
tion. The input capacitor sees this as AC current, and
dissipates power proportional to the RMS value of the
input current waveform. To properly specify the capaci-
tor, we need to know the RMS value of the input current.
Calculating the approximate RMS value of a pulse train
with a fixed duty cycle is straightforward, but the LTC1702
complicates matters by running two sides simultaneously
and out of phase, creating a complex waveform at the
input.
To calculate the approximate RMS value of the input
current, we first need to calculate the average DC value
with both sides of the LTC1702 operating at maximum
load. Over a single period, the system will spend some
time with one top switch on and the other off, perhaps
some time with both switches on, and perhaps some
time with both switches off. During the time each top
switch is on, the current will equal that side’s full load
output current. When both switches are on, the total
current will be the sum of the two full load currents, and
when both are off, the current is effectively zero. Multiply
each current value by the percentage of the period that
the current condition lasts, and sum the results—this is
the average DC current value.
10A
0
32%
68%
Q1 CURRENT, SIDE 1 ONLY
(FOR 1-PHASE, 2 SIDES:
MULTIPLY CURRENT BY 2)
As an example, consider a circuit that takes a 5V input
and generates 3.3V at 3A at side 1 and 1.6V at 10A at
side 2. When a cycle starts, TG1 turns on and 3A flows
32%
6.8A
0
68%
CURRENT IN C IN , SIDE 1 ONLY
I CIN = 4.66A RMS , (1-PHASE,
2 SIDES: I CIN = 9.3A RMS )
13
50%
16% 16% 18%
–3.2A
10A
32% 18% 32% 18%
Q11 CURRENT
Q21 CURRENT
10
0
BOTH SIDES EQUAL LOAD
2-PHASE OPERATION
5.2
3
I AVE
32% 18% 32% 18%
3.6A
0
–6.4A
CURRENT IN C IN ,
BOTH SIDES EQUAL LOAD
I CIN = 4.8A RMS
1702 F07
0
0
A
B
TIME
C
D
1702 SB1
Figure 7. RMS Input Current
Figure SB1. Average Current Calculation
1702fa
18
相关PDF资料 |
PDF描述 |
|---|---|
| RSC18DRTS | CONN EDGECARD 36POS DIP .100 SLD |
| H2AAT-10103-R4-ND | JUMPER-H1502TR/A2015R/H1502TR 3" |
| VE-25Z-EU-F1 | CONVERTER MOD DC/DC 2V 80W |
| SLP682M025C1P3 | CAP ALUM 6800UF 25V 20% SNAP |
| H2AAT-10103-N4-ND | JUMPER-H1502TR/A2015N/H1502TR 3" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1702IGN#PBF | 功能描述:IC REG CTRLR BUCK PWM VM 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1702IGN#TR | 功能描述:IC REG CTRLR BUCK PWM VM 24-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1702IGN#TRPBF | 功能描述:IC REG CTRLR BUCK PWM VM 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1703CG | 功能描述:IC REG SW DUAL SYNC VID 28SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC1703CG#PBF | 功能描述:IC REG SW DUAL SYNC VID 28SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。