- 您现在的位置：买卖IC网 > PDF目录15277 > LTC1709EG-8 (Linear Technology)IC REG CTRLR BUCK PWM CM 36-SSOP PDF资料下载
参数资料
| 型号： | LTC1709EG-8 |
| 厂商： | Linear Technology |
| 文件页数： | 18/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 36-SSOP |
| 标准包装： | 37 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 360kHz |
| 占空比： | 99.5% |
| 电源电压： | 4 V ~ 36 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 36-SSOP（0.209"，5.30mm 宽） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC1709-8/LTC1709-9
APPLICATIO S I FOR ATIO
Each VID digital input is pulled up by a 40k resistor in
The time for the output current to ramp up is then:
series with a diode from V BIAS . Therefore, it must be
grounded to get a digital low input, and can be either
floated or connected to V BIAS to get a digital high input. The
series diode is used to prevent the digital inputs from
t IRAMP =
3 V ? 1. 5 V
1 . 2 μ A
C SS = ( 1 . 25 s / μ F ) C SS
being damaged or clamped if they are driven higher than
V BIAS . The digital inputs accept CMOS voltage levels.
V BIAS is the supply voltage for the VID section. It is
normally connected to INTV CC but can be driven from
other sources. If it is driven from another source, that
source must be in the range of 2.7V to 5.5V and must be
alive prior to enabling the LTC1709.
By pulling the RUN/SS pin below 0.8V the LTC1709 is put
into low current shutdown (I Q < 40 μ A). The RUN/SS pins
can be driven directly from logic as shown in Figure 6.
Diode D1 in Figure 6 reduces the start delay but allows
C SS to ramp up slowly providing the soft-start function.
The RUN/SS pin has an internal 6V zener clamp (see
Functional Diagram).
Soft-Start/Run Function
3.3V OR 5V
V IN
RUN/SS
INTV CC
The RUN/SS pin provides three functions: 1) Run/Shut-
down, 2) soft-start and 3) a defeatable short-circuit latchoff
timer. Soft-start reduces the input power sources’ surge
D1
R SS *
C SS
D1*
R SS *
RUN/SS
currents by gradually increasing the controller’s current
limit I TH(MAX) . The latchoff timer prevents very short,
C SS
extreme load transients from tripping the overcurrent
latch. A small pull-up current (>5 μ A) supplied to the RUN/
SS pin will prevent the overcurrent latch from operating.
The following explanation describes how the functions
*OPTIONAL TO DEFEAT OVERCURRENT LATCHOFF
Figure 6. RUN/SS Pin Interfacing
170989 F06
operate.
An internal 1.2 μ A current source charges up the soft-start
capacitor, C SS . When the voltage on RUN/SS reaches
1.5V, the controller is permitted to start operating. As the
voltage on RUN/SS increases from 1.5V to 3.0V, the
internal current limit is increased from 25mV/R SENSE to
75mV/R SENSE . The output current limit ramps up slowly,
taking an additional 1.4s/ μ F to reach full current. The
output current thus ramps up slowly, reducing the starting
surge current required from the input power supply. If
RUN/SS has been pulled all the way to ground there is a
delay before starting of approximately:
Fault Conditions: Overcurrent Latchoff
The RUN/SS pin also provides the ability to latch off the
controllers when an overcurrent condition is detected. The
RUN/SS capacitor, C SS , is used initially to limit the inrush
current of both controllers. After the controllers have been
started and been given adequate time to charge up the
output capacitors and provide full load current, the RUN/
SS capacitor is used for a short-circuit timer. If the output
voltage falls to less than 70% of its nominal value after C SS
reaches 4.1V, C SS begins discharging on the assumption
that the output is in an overcurrent condition. If the
condition lasts for a long enough period as determined by
t DELAY =
1 . 5 V
1 . 2 μ A
C SS = ( 1 . 25 s / μ F ) C SS
the size of the C SS , the controller will be shut down until the
RUN/SS pin voltage is recycled. If the overload occurs
during start-up, the time can be approximated by:
t LO1 ≈ (C SS ? 0.6V)/(1.2 μ A) = 5 ? 10 5 (C SS )
18
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1709EG-9#PBF | IC REG CTRLR BUCK PWM CM 36-SSOP |
| LTC1709EG-9 | IC REG CTRLR BUCK PWM CM 36-SSOP |
| LTC1775CS#TRPBF | IC REG CTRLR BUCK PWM CM 16-SOIC |
| LTC1775CS#TR | IC REG CTRLR BUCK PWM CM 16-SOIC |
| H4BBT-10112-G1-ND | JUMPER-H9992TR/A3047G/H9992TR12" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1709EG-8#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 36-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 包装:带卷 (TR) |
| LTC1709EG-8#TR | 功能描述:IC REG CTRLR BUCK PWM CM 36-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1709EG-8#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 36-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1709EG-85 | 功能描述:IC REG CTRLR BUCK PWM CM 36-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC1709EG-85#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 36-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
发布紧急采购，3分钟左右您将得到回复。