- 您现在的位置：买卖IC网 > PDF目录11806 > LTC1755EGN#PBF (Linear Technology)IC SMART CARD INTERFACE 24SSOP PDF资料下载
参数资料
| 型号： | LTC1755EGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/16页 |
| 文件大小： | 0K |
| 描述： | IC SMART CARD INTERFACE 24SSOP |
| 标准包装： | 55 |
| 应用： | 智能卡 |
| 电源电压： | 2.7 V ~ 6 V |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-SSOP |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
| 产品目录页面： | 1355 (CN2011-ZH PDF) |
8
LTC1755/LTC1756
microseconds then the LTC1755/LTC1756 switch to the
Alarm state. This fault checking is only performed after the
VCC pin has reached its final value (as indicated by the
READY pin).
The clock channel is optimized for signal integrity in order
to meet the stringent duty cycle requirements of the EMV
specification. Therefore, to reduce power in low power
applications, clock stop mode is recommended when data
is not being exchanged.
CIN (Pins 13/9): (Input) Clock Input Pin from the Micro-
controller. During the Active state this signal appears on
the CLK pin after being level-shifted and buffered.
DVCC sets the logic reference level for the CIN pin.
RIN (Pins 14/10): (Input) Reset Input Pin from the Micro-
controller. During the Active state this signal appears on
the RST pin after being level-shifted and buffered.
DVCC sets the logic reference level for the RIN pin.
DATA (Pins 15/11): (Input/Output) Microcontroller Side
Data I/O Pin. This pin is used for bidirectional data transfer
between the microcontroller and the Smart Card. The
microcontroller data pin must be open drain and must be
able to sink up to 250
A when driving the DATA pin low
due to the pull-up current source. The DATA pin becomes
high impedance during the Idle state or when CS is high
(see the State Diagram). It does not become active until the
READY signal goes low indicating that VCC is stable.
AUX2IN (Pin 16, LTC1755 Only): (Input/Output) Micro-
controller Side Auxiliary I/O pin. This pin is used for
bidirectional auxiliary data transfer between the micro-
controller and the Smart Card. It has the same character-
istics as the DATA pin.
AUX1IN (Pin 17, LTC1755 Only): (Input/Output) Micro-
controller Side Auxiliary I/O Pin. This pin is used for
bidirectional auxiliary data transfer between the micro-
controller and the Smart Card. It has the same character-
istics as the DATA pin.
C+, C– (Pins 18/12, 19/13): Charge Pump Flying Capaci-
tor Terminals. Optimum values for the flying capacitor
range from 0.68
F to 1F. Best performance is achieved
with a low ESR X7R ceramic capacitor.
DVCC (Pin 20, LTC1755 Only): Supply Voltage for the
Microcontroller Side Digital Input and Input/Output Pins
(Typically 3V). If the charge pump input pin (VIN) is
powered from the same source as the microcontroller,
then DVCC should be connected directly to VIN. In this case
only one (10
F) input bypass capacitor is needed for the
LTC1755. If the DVCC pin is powered separately then it
should be bypassed separately with a 0.1
F capacitor. The
DVCC pin may be between 2V and 5.5V.
The DVCC pin is monitored for adequate voltage. If DVCC
drops below approximately 1.5V the LTC1755 automati-
cally enters the Idle state. On the LTC1756, DVCC is
connected internally to VIN.
READY (Pins 21/14): (Output) Readiness Indicator of the
Smart Card Supply Voltage (VCC). When the LTC1755/
LTC1756 are placed in the Active state the soft-start
feature slowly ramps the VCC voltage. A low on the READY
pin indicates that VCC has reached its final value.
The READY pin also indicates if the LTC1756 is in Alarm
mode. The LTC1756 detects faults such as VCCunderrange
for at least 5
s, overtemperature shutdown, CLK or RST
invalid output levels and card removal during Active
state. CLK or RST invalid and overtemperature faults are
detected only after VCC has reached its final value. VCC
underrange and card removal during Active faults are
detected at any time during the Active period (i.e., once
PWR = 0V).
If the LTC1756 has been activated normally and VCC, the
card voltage, has reached its final value then READY will
go low indicating normal operation. If, following this, a
fault occurs and the LTC1756 enters the Alarm state, the
READY pin will return high.
In the event that a fault precedes the activation of VCC,
such as a direct short circuit from VCC to GND, the
LTC1756 will attempt to operate until the fault is detected
and then automatically shut down and enter the Alarm
state. In this case the READY pin will never go low after the
command to start the smart card is given (i.e., PWR = 0V).
If the LTC1755/LTC1756 enter the Alarm state they can
only be cleared by returning the PWR pin high.
UU
U
PI FU CTIO S LTC1755/LTC1756
相关PDF资料 |
PDF描述 |
|---|---|
| AT32UC3C264C-A2UR | IC MCU AVR32 64K FLASH 64TQFP |
| LTC1756EGN#PBF | IC SMART CARD INTERFACE 16SSOP |
| AT89C51IC2-RLRUL | IC 8051 MCU 32K FLASH 44-VQFP |
| ATMEGA645V-8AUR | MCU AVR 64KB FLASH 8MHZ 64TQFP |
| ATMEGA645-16AUR | MCU AVR 64KB FLASH 16MHZ 64TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1755ENG#PBF | 制造商:LT 功能描述: |
| LTC1756EGN | 功能描述:IC SMART CARD 16-SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| LTC1756EGN#PBF | 功能描述:IC SMART CARD INTERFACE 16SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| LTC1756EGN#TR | 功能描述:IC SMART CARD INTERFACE 16SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| LTC1756EGN#TRPBF | 功能描述:IC SMART CARD INTERFACE 16SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
发布紧急采购，3分钟左右您将得到回复。