- 您现在的位置：买卖IC网 > PDF目录11806 > LTC1755EGN#PBF (Linear Technology)IC SMART CARD INTERFACE 24SSOP PDF资料下载
参数资料
| 型号： | LTC1755EGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 4/16页 |
| 文件大小： | 0K |
| 描述： | IC SMART CARD INTERFACE 24SSOP |
| 标准包装： | 55 |
| 应用： | 智能卡 |
| 电源电压： | 2.7 V ~ 6 V |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-SSOP |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
| 产品目录页面： | 1355 (CN2011-ZH PDF) |
12
LTC1755/LTC1756
5V/
s, the following expression for RPULL-UP should be
applied:
R
VV
CpF
PULL UP
SUPPLY
PAR
= ()()
–
1
50
5 106
where CPAR is the extra capacitance on the bidirectional
pin and VSUPPLY is the minimum local supply for the
bidirectional pin. For example, on the smart card side, 3V
should be assumed for VSUPPLY.
Note that the addition of a pull-up resistor will give a higher
output voltage when the bidirectional pin pulls down. Care
should be taken so that the VIL or VOL specifications are not
compromised with this technique.
Bidirectional Channels
As described in Pin Functions (Pins 10/6), the bidirec-
tional channels allow transmission in only one direction at
a time. Figure 2 shows a simplified block diagram of one
of the three bidirectional channels. The three channels
operate in an identical fashion.
Figure 3 shows an example of normal transmit and receive
operations as well as the two possible collision scenarios.
If a channel is activated from one direction and an L is
imposed in the other direction before both sides return H
a collision results. The result of the collision is that the
receiving side (
Slave Side) will remain low until it is
released, but the transmitting side (first side to go low or
Master Side), will be allowed to return high if released. The
colliding L externally imposed on the slave side will not be
transmitted back through the channel.
released by comparing its slew rate with an internal
reference value. If a valid transition is detected, a large
pull-up current enhances the edge rate on the node. The
higher slew rate corroborates the decision to charge the
node thereby effecting a dynamic form of hysteresis. Once
the node has reached the power supply voltage the internal
comparator requires several hundred nanoseconds to
reset. Pulling down on the pin before the reset delay
expires will result in a momentary contention and a higher
current flow. Therefore, the comparator delay sets the
upper limit on the maximum data rate of the bidirectional
channels to about 500kHz.
The dynamic pull-up current sources are designed to
trigger with as much as 50pF of capacitive load on the
bidirectional pins. At approximately 90pF (or greater), the
edge rate on the node will be insufficient to trigger the edge
rate detector and the node will only ramp up at a rate given
by the ISTART current source and the load capacitance. In
these instances the edge rate of the bidirectional pin may
not meet the requirements of existing smart card stan-
dards. Therefore, it is recommended that the sum of both
explicit and parasitic capacitances on the bidirectional
pins be kept below 50pF.
If excessive capacitance (either explicit or parasitic) is
present on the bidirectional pins, the starting pull-up
current must also be increased. This can be accomplished
with a pull-up resistor to the respective supply. For the
smart card side (I/O, AUX1 and AUX2), the pull-up resis-
tor should be connected to VCC. For the microcontroller
side (DATA, AUX1IN and AUX2IN), the pull-up resistor
should be connected to DVCC on the LTC1755 (VIN on the
LTC1756). To maintain an edge rate of approximately
APPLICATIO S I FOR ATIO
WU
UU
DVCC
CS
DATA
CHARGE
PUMP
BIDIRECTIONAL
LATCH
I/O
TO
SMART CARD
TO
MICROCONTROLLER
VCC
READY
3.5mA
17756 F02
Figure 2. Bidirectional Channel Simplified Block Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| AT32UC3C264C-A2UR | IC MCU AVR32 64K FLASH 64TQFP |
| LTC1756EGN#PBF | IC SMART CARD INTERFACE 16SSOP |
| AT89C51IC2-RLRUL | IC 8051 MCU 32K FLASH 44-VQFP |
| ATMEGA645V-8AUR | MCU AVR 64KB FLASH 8MHZ 64TQFP |
| ATMEGA645-16AUR | MCU AVR 64KB FLASH 16MHZ 64TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1755ENG#PBF | 制造商:LT 功能描述: |
| LTC1756EGN | 功能描述:IC SMART CARD 16-SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| LTC1756EGN#PBF | 功能描述:IC SMART CARD INTERFACE 16SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| LTC1756EGN#TR | 功能描述:IC SMART CARD INTERFACE 16SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| LTC1756EGN#TRPBF | 功能描述:IC SMART CARD INTERFACE 16SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
发布紧急采购，3分钟左右您将得到回复。