- 您现在的位置：买卖IC网 > PDF目录15326 > LTC1771EMS8 (Linear Technology)IC REG CTRLR BUCK PWM CM 8-MSOP PDF资料下载
参数资料
| 型号： | LTC1771EMS8 |
| 厂商： | Linear Technology |
| 文件页数： | 6/16页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 8-MSOP |
| 标准包装： | 50 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 占空比： | 100% |
| 电源电压： | 2.8 V ~ 18 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 包装： | 管件 |
| 其它名称： | Q1164777 |
LTC1771
OPERATIO
Main Control Loop
(Refer to Functional Block Diagram)
Burst Mode operation is provided by clamping the mini-
The LTC1771 uses a constant off-time, current mode
step-down architecture. During normal operation, the
P-channel MOSFET is turned on at the beginning of each
cycle and turned off when the current comparator C
triggers the 1-shot timer. The external MOSFET switch
stays off for the 3.5 μ s 1-shot duration and then turns back
on again to begin a new cycle. The peak inductor current
at which C triggers the 1-shot is controlled by the voltage
on Pin 3 (I TH ), the output of the error amplifier EA. An
external resistive divider connected between V OUT and
ground allows EA to receive an output feedback voltage
V FB . When the load current increases, it causes a slight
decrease in V FB relative to the 1.23V reference, which in
turn causes the I TH voltage to increase until the average
inductor current matches the new load current.
The main control loop is shut down by pulling Pin 1
(RUN/SS) low. Releasing RUN/SS allows an internal 1 μ A
current source to charge soft-start capacitor C SS . When
C SS reaches 1V, the main control loop is enabled with the
I TH voltage clamped at approximately 40% of its maxi-
mum value. As C SS continues to charge, I TH is gradually
released allowing normal operation to resume.
Burst Mode Operation
The LTC1771 provides outstanding low current efficiency
and ultralow no-load supply current by using Burst Mode
operation when the MODE pin is pulled above 2V. During
Burst Mode operation, short burst cycles of normal switch-
ing are followed by a longer idle period with the switch off
and the load current is supplied by the output capacitor.
During this idle period, only the minimum required cir-
cuitry—1.23V reference and error amp—are left on, and
the supply current is reduced to 9 μ A. At no load, the output
capacitor is still discharged very slowly by leakage current
in the Schottky diode and feedback resistor current result-
ing in very low frequency burst cycles that add a few more
microamps to the supply current.
6
mum I TH voltage at 1V which represents about 25% of
maximum load current. If the load falls below this level, i.e.
the I TH voltage tries to fall below 1V, the burst comparator
B switches state signaling the LTC1771 to enter sleep
mode. During this time, EA is reduced to 10% of its normal
operating current and the external compensation capaci-
tor is disconnected and clamped to 1V so that the EA can
drive its output with the lower available current. As the load
discharges the output capacitor, the internal I TH voltage
increases. When it exceeds 1V the burst comparator exits
sleep mode, reconnects the external compensation com-
ponents to the error amplifier output, and returns EA to full
power along with the other necessary circuitry. This
scheme (patent pending) allows the EA to be reduced to
such a low operating current during sleep mode without
adding unacceptable delay to wake up the LTC1771 due to
the compensation capacitor on I TH required for stability in
normal operation.
Burst Mode operation can be disabled by pulling the
MODE pin to ground. In this mode of operation, the burst
comparator B is disabled and the I TH voltage allowed to go
all the way to 0V. The load can now be reduced to about 1%
of maximum load before the loop skips cycles to maintain
regulation. This mode provides a low noise output spec-
trum, useful for reducing both audio and RF interference,
at the expense of reduced efficiency at light loads.
Off-Time
The off-time duration is 3.5 μ s when the feedback voltage
is close to the reference voltage; however, as the feedback
voltage drops, the off-time lengthens and reaches a maxi-
mum value of about 70 μ s when V FB is zero. This ensures
that the inductor current has enough time to decay when
the reverse voltage across the inductor is low such as
during short circuit, thus protecting the MOSFET and
inductor.
相关PDF资料 |
PDF描述 |
|---|---|
| GMM10DTMN-S273 | CONN EDGECARD 20POS R/A .156 SLD |
| VI-JWT-EY-F4 | CONVERTER MOD DC/DC 6.5V 50W |
| IMC1210BN330J | INDUCTOR WW 33UH 5% 1210 |
| ADM805LARN | IC SUPERVISOR 4.65V WD 8SOIC |
| GSM10DTMD-S273 | CONN EDGECARD 20POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1771EMS8#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC1771EMS8#PBF | 制造商:Linear Technology 功能描述:IC STEP-DOWN DC/DC CONTROLLER MSOP-8 制造商:Linear Technology 功能描述:IC, STEP-DOWN DC/DC CONTROLLER, MSOP-8 |
| LTC1771EMS8#TR | 功能描述:IC REG CTRLR BUCK PWM CM 8-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1771EMS8#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1771EMS8PBF | 制造商:Linear Technology 功能描述:PWM Controller Current 1.23-18V 5A MSOP8 |
发布紧急采购，3分钟左右您将得到回复。