- 您现在的位置：买卖IC网 > PDF目录15326 > LTC1771EMS8 (Linear Technology)IC REG CTRLR BUCK PWM CM 8-MSOP PDF资料下载
参数资料
| 型号： | LTC1771EMS8 |
| 厂商： | Linear Technology |
| 文件页数： | 7/16页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 8-MSOP |
| 标准包装： | 50 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 占空比： | 100% |
| 电源电压： | 2.8 V ~ 18 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 包装： | 管件 |
| 其它名称： | Q1164777 |
LTC1771
APPLICATIO S I FOR ATIO
The basic LTC1771 application circuit is shown in Figure
1 on the first page. External component selection is driven
by the load requirement and begins with the selection of
R SENSE . Once R SENSE is known, L can be chosen. Next, the
MOSFET and D1 are selected. The inductor is chosen
based largely on the desired amount of ripple current and
for Burst Mode operation. Finally C IN is selected for its
ability to handle the required RMS input current and C OUT
is chosen with low enough ESR to meet the output voltage
ripple and transient specifications.
R SENSE Selection
R SENSE is chosen based on the required output current.
The LTC1771 current comparator has a maximum thresh-
old of 140mV/R SENSE . The current comparator threshold
sets the peak inductor current, yielding a maximum aver-
age output current I MAX equal to the peak less half the
peak-to-peak ripple current ? I L . For best performance
when Burst Mode operation is enabled, choose ? I L equal
to 35% of peak current. Allowing a margin for variations in
the LTC1771 and external components gives the following
equation for choosing R SENSE :
R SENSE = 100mV/I MAX
At higher supply voltages, the peak currents may be
slightly higher due to overshoot from current comparator
delay and can be predicted from the second term in the
following equation:
where t OFF = 3.5 μ s. However, the ripple current at low
loads during Burst Mode operation is:
? I L(BURST) ≈ 35% of I PEAK ≈ 0.05/R SENSE
For best efficiency when Burst Mode operation is enabled,
choose:
? I L(CONT) ≤ ? I L(BURST)
so that the inductor current is continuous during the burst
periods. This sets a minimum inductor value of:
L MIN = (75 μ H)(V OUT + V D )(R SENSE )
When burst is disabled, ripple currents less than ? I L(BURST)
can be achieved by choosing L > L MIN . Lower ripple
current reduces output voltage ripple and core losses, but
too low of ripple current will adversely effect efficiency.
Inductor Core Selection
Once the value of L is known, the type of inductor must be
selected. High efficiency converters generally cannot
afford the core loss found in low cost powdered iron
cores, forcing the use of more expensive ferrite,
molypermalloy or Kool M μ ? cores. Actual core loss is
independent of core size for a fixed inductor value, but is
very dependent on inductance selected. As inductance
increases, core losses go down. Unfortunately, increased
inductance requires more turns of wire and therefore
copper losses will increase.
? + 0 . 5 ? IN OUT ?
I PEAK
0 . 14 ? V – V ?
R SENSE ? L ( μ H ) ?
1 / 2
Ferrite designs have very low core loss and are preferred
at high switching frequencies, so design goals can con-
centrate on copper loss and preventing saturation. Ferrite
core material saturates “hard,” which means that induc-
? I L ( CONT ) = t OFF ? OUT D ?
Inductor Value Selection
Once R SENSE is known, the inductor value can be deter-
mined. The inductance value has a direct effect on ripple
current. The ripple current decreases with higher induc-
tance and increases with higher V OUT . The ripple current
during continuous mode operation is set by the off-time
and inductance to be:
? V + V ?
? L ?
Kool M μ is a registered trademark of Magnetics, Inc.
tance collapses abruptly when the peak design current is
exceeded. This results in an abrupt increase in inductor
ripple current and consequent increase in voltage ripple.
Do not allow the core to saturate!
Molypermalloy (from Magnetics, Inc.) is a very good, low
loss core material for toroids, but it is more expensive than
ferrite. A reasonable compromise from the same manu-
facturer is Kool M μ . Toroids are space efficient, especially
when you can use several layers of wire. Because they
generally lack a bobbin, mounting is more difficult. How-
ever, designs for surface mount are available that do not
increase the height significantly.
7
相关PDF资料 |
PDF描述 |
|---|---|
| GMM10DTMN-S273 | CONN EDGECARD 20POS R/A .156 SLD |
| VI-JWT-EY-F4 | CONVERTER MOD DC/DC 6.5V 50W |
| IMC1210BN330J | INDUCTOR WW 33UH 5% 1210 |
| ADM805LARN | IC SUPERVISOR 4.65V WD 8SOIC |
| GSM10DTMD-S273 | CONN EDGECARD 20POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1771EMS8#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC1771EMS8#PBF | 制造商:Linear Technology 功能描述:IC STEP-DOWN DC/DC CONTROLLER MSOP-8 制造商:Linear Technology 功能描述:IC, STEP-DOWN DC/DC CONTROLLER, MSOP-8 |
| LTC1771EMS8#TR | 功能描述:IC REG CTRLR BUCK PWM CM 8-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1771EMS8#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1771EMS8PBF | 制造商:Linear Technology 功能描述:PWM Controller Current 1.23-18V 5A MSOP8 |
发布紧急采购，3分钟左右您将得到回复。