- 您现在的位置：买卖IC网 > PDF目录15348 > LTC1772ES6#TR (Linear Technology)IC REG CTRLR BUCK PWM CM SOT23-6 PDF资料下载
参数资料
| 型号： | LTC1772ES6#TR |
| 厂商： | Linear Technology |
| 文件页数： | 5/12页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM SOT23-6 |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 650kHz |
| 占空比： | 100% |
| 电源电压： | 2.5 V ~ 9.8 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | SOT-23-6 细型，TSOT-23-6 |
| 包装： | 带卷 (TR) |
LTC1772
OPERATIO
Main Control Loop
(Refer to Functional Diagram)
oscillator cycle will turn the external MOSFET on and the
The LTC1772 is a constant frequency current mode switch-
ing regulator. During normal operation, the external
P-channel power MOSFET is turned on each cycle when
the oscillator sets the RS latch (RS1) and turned off when
the current comparator (ICMP) resets the latch. The peak
inductor current at which ICMP resets the RS latch is
controlled by the voltage on the I TH /RUN pin, which is the
output of the error amplifier EAMP. An external resistive
divider connected between V OUT and ground allows the
EAMP to receive an output feedback voltage V FB . When the
load current increases, it causes a slight decrease in V FB
relative to the 0.8V reference, which in turn causes the
I TH /RUN voltage to increase until the average inductor
current matches the new load current.
The main control loop is shut down by pulling the I TH /RUN
pin low. Releasing I TH /RUN allows an internal 0.5 μ A
current source to charge up the external compensation
network. When the I TH /RUN pin reaches 0.35V, the main
control loop is enabled with the I TH /RUN voltage then
pulled up to its zero current level of approximately 0.7V.
As the external compensation network continues to charge
up, the corresponding output current trip level follows,
allowing normal operation.
Comparator OVP guards against transient overshoots
> 7.5% by turning off the external P-channel power
MOSFET and keeping it off until the fault is removed.
Burst Mode Operation
The LTC1772 enters Burst Mode operation at low load
currents. In this mode, the peak current of the inductor is
set as if V ITH /RUN = 1V (at low duty cycles) even though
the voltage at the I TH /RUN pin is at a lower value. If the
inductor’s average current is greater than the load require-
ment, the voltage at the I TH /RUN pin will drop. When the
I TH /RUN voltage goes below 0.85V, the sleep signal goes
high, turning off the external MOSFET. The sleep signal
goes low when the I TH /RUN voltage goes above 0.925V
switching cycle repeats.
Dropout Operation
When the input supply voltage decreases towards the
output voltage, the rate of change of inductor current
during the ON cycle decreases. This reduction means that
the external P-channel MOSFET will remain on for more
than one oscillator cycle since the inductor current has not
ramped up to the threshold set by EAMP. Further reduc-
tion in input supply voltage will eventually cause the
P-channel MOSFET to be turned on 100%, i.e., DC. The
output voltage will then be determined by the input voltage
minus the voltage drop across the MOSFET, the sense
resistor and the inductor.
Undervoltage Lockout
To prevent operation of the P-channel MOSFET below safe
input voltage levels, an undervoltage lockout is incorpo-
rated into the LTC1772. When the input supply voltage
drops below approximately 2.0V, the P-channel MOSFET
and all circuitry is turned off except the undervoltage block,
which draws only several microamperes.
Short-Circuit Protection
When the output is shorted to ground, the frequency of the
oscillator will be reduced to about 120kHz. This lower
frequency allows the inductor current to safely discharge,
thereby preventing current runaway. The oscillator’s fre-
quency will gradually increase to its designed rate when
the feedback voltage again approaches 0.8V.
Overvoltage Protection
As a further protection, the overvoltage comparator in the
LTC1772 will turn the external MOSFET off when the
feedback voltage has risen 7.5% above the reference
voltage of 0.8V. This comparator has a typical hysteresis
of 20mV.
and the LTC1772 resumes normal operation. The next
1772fb
5
相关PDF资料 |
PDF描述 |
|---|---|
| RMM11DRAI | CONN EDGECARD 22POS R/A .156 SLD |
| URU2F220MHD | CAP ALUM 22UF 315V 20% RADIAL |
| LTC1326IS8#TRPBF | IC PREC TRPL SUPPLY MONITR 8SOIC |
| VI-BWY-EY-B1 | CONVERTER MOD DC/DC 3.3V 33W |
| RCM43DCTN | CONN EDGECARD 86POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1772HS6#TRMPBF | 功能描述:IC REG CTRLR BUCK PWM CM SOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1772HS6#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM SOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC1772IS6 | 制造商:Linear Technology 功能描述:DC DC Cntrlr Single-OUT Step Down 2.5V to 9.8V Input 6-Pin TSOT-23 |
| LTC1772IS6#PBF | 制造商:Linear Technology 功能描述:DC DC Cntrlr Single-OUT Step Down 2.5V to 9.8V Input 6-Pin TSOT-23 |
| LTC1772IS6#TR | 功能描述:IC REG CTRLR BUCK PWM CM SOT23-6 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。