参数资料
| 型号： | LTC2240CUP-12#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/30页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 170MSPS 64-QFN |
| 标准包装： | 40 |
| 位数： | 12 |
| 采样率（每秒）： | 170M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 638mW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-WFQFN 裸露焊盘 |
| 供应商设备封装： | 64-QFN（9x9） |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC2240-12
23
224012fd
APPLICATIONS INFORMATION
some source termination to reduce ringing that may occur
even over a fraction of an inch is advisable. You must not
allow the clock to overshoot the supplies or performance
will suffer. Do not lter the clock signal with a narrow band
lter unless you have a sinusoidal clock source, as the
rise and fall time artifacts present in typical digital clock
signals will be translated into phase noise.
The lowest phase noise oscillators have single-ended si-
nusoidal outputs, and for these devices the use of a lter
close to the ADC may be benecial. This lter should be
close to the ADC to both reduce roundtrip reection times,
as well as reduce the susceptibility of the traces between
the lter and the ADC. If the circuit is sensitive to close-
in phase noise, the power supply for oscillators and any
buffers must be very stable, or propagation delay variation
with supply will translate into phase noise. Even though
these clock sources may be regarded as digital devices,
do not operate them on a digital supply. If your clock is
also used to drive digital devices such as an FPGA, you
should locate the oscillator, and any clock fan-out devices
close to the ADC, and give the routing to the ADC prece-
dence. The clock signals to the FPGA should have series
termination at the driver to prevent high frequency noise
from the FPGA disturbing the substrate of the clock fan-out
device. If you use an FPGA as a programmable divider, you
must re-time the signal using the original oscillator, and
the re-timing ip-op as well as the oscillator should be
close to the ADC, and powered with a very quiet supply.
For cases where there are multiple ADCs, or where the
clock source originates some distance away, differential
clock distribution is advisable. This is advisable both from
the perspective of EMI, but also to avoid receiving noise
from digital sources both radiated, as well as propagated in
the waveguides that exist between the layers of multilayer
PCBs. The differential pairs must be close together and
distanced from other signals. The differential pair should
be guarded on both sides with copper distanced at least
3x the distance between the traces, and grounded with
vias no more than 1/4 inch apart.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2240IUP-10#PBF | IC ADC 10BIT 170MSPS 64-QFN |
| LTC2241IUP-10#PBF | IC ADC 10BIT 210MSPS 64-QFN |
| LTC2242IUP-10#PBF | IC ADC 10BIT 250MSPS 64-QFN |
| LTC2245IUH#TRPBF | IC ADC 14BIT 10MSPS 3V 32-QFN |
| LTC2249IUH#TRPBF | IC ADC 14BIT 80MSPS LP 32-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2240CUP-12-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:12-Bit, 170Msps ADC |
| LTC2240CUP-12-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:12-Bit, 170Msps ADC |
| LTC2240IUP-10 | 制造商:LINER 制造商全称:Linear Technology 功能描述:10-Bit, 170Msps ADC |
| LTC2240IUP-10#PBF | 功能描述:IC ADC 10BIT 170MSPS 64-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| LTC2240IUP-10#TRPBF | 功能描述:IC ADC 10BIT 170MSPS 64-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。