参数资料
| 型号： | LTC2242IUP-10#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 6/30页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 250MSPS 64-QFN |
| 标准包装： | 40 |
| 位数： | 10 |
| 采样率（每秒）： | 250M |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 975mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-WFQFN 裸露焊盘 |
| 供应商设备封装： | 64-QFN（9x9） |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，双极 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC2242-10
14
224210fd
applicaTions inForMaTion
DYNAMIC PERFORMANCE
Signal-to-Noise Plus Distortion Ratio
The signal-to-noise plus distortion ratio [S/(N + D)] is
the ratio between the RMS amplitude of the fundamen-
tal input frequency and the RMS amplitude of all other
frequency components at the ADC output. The output is
band limited to frequencies above DC to below half the
sampling frequency.
Signal-to-Noise Ratio
The signal-to-noise ratio (SNR) is the ratio between the
RMS amplitude of the fundamental input frequency and
the RMS amplitude of all other frequency components
except the first five harmonics and DC.
Total Harmonic Distortion
Total harmonic distortion is the ratio of the RMS sum
of all harmonics of the input signal to the fundamental
itself. The out-of-band harmonics alias into the frequency
band between DC and half the sampling frequency. THD
is expressed as:
THD
= 20Log
V22
+ V32 + V42 +...Vn2
(
)/V1
where V1 is the RMS amplitude of the fundamental fre-
quencyandV2throughVnaretheamplitudesofthesecond
through nth harmonics. The THD calculated in this data
sheet uses all the harmonics up to the fifth.
Intermodulation Distortion
If the ADC input signal consists of more than one spectral
component, the ADC transfer function nonlinearity can
produce intermodulation distortion (IMD) in addition to
THD. IMD is the change in one sinusoidal input caused
by the presence of another sinusoidal input at a different
frequency.
If two pure sine waves of frequencies fa and fb are ap-
plied to the ADC input, nonlinearities in the ADC transfer
function can create distortion products at the sum and
difference frequencies of mfa ± nfb, where m and n = 0,
1, 2, 3, etc. The 3rd order intermodulation products are
2fa + fb, 2fb + fa, 2fa – fb and 2fb – fa. The intermodula-
tion distortion is defined as the ratio of the RMS value of
either input tone to the RMS value of the largest 3rd order
intermodulation product.
Spurious Free Dynamic Range (SFDR)
Spuriousfreedynamicrangeisthepeakharmonicorspuri-
ous noise that is the largest spectral component excluding
the input signal and DC. This value is expressed in decibels
relative to the RMS value of a full scale input signal.
Full Power Bandwidth
The full power bandwidth is that input frequency at which
theamplitudeofthereconstructedfundamentalisreduced
by 3dB for a full scale input signal.
Aperture Delay Time
The time from when a rising ENC+ equals the ENC– voltage
to the instant that the input signal is held by the sample
and hold circuit.
Aperture Delay Jitter
The variation in the aperture delay time from conversion
to conversion. This random variation will result in noise
when sampling an AC input. The signal to noise ratio due
to the jitter alone will be:
SNRJITTER = –20log (2π fIN tJITTER)
CONVERTER OPERATION
As shown in Figure 1, the LTC2242-10 is a CMOS pipelined
multi-step converter. The converter has five pipelined ADC
stages; a sampled analog input will result in a digitized
valuefivecycleslater(seetheTimingDiagramsection).For
optimal performance the analog inputs should be driven
differentially. The encode input is differential for improved
common mode noise immunity. The LTC2242-10 has two
phases of operation, determined by the state of the dif-
ferential ENC+/ENC– input pins. For brevity, the text will
refer to ENC+ greater than ENC– as ENC high and ENC+
less than ENC– as ENC low.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC2245IUH#TRPBF | IC ADC 14BIT 10MSPS 3V 32-QFN |
| LTC2249IUH#TRPBF | IC ADC 14BIT 80MSPS LP 32-QFN |
| LTC2251IUH#PBF | IC ADC 10-BIT 125MSPS 3V 32-QFN |
| LTC2253IUH#TRPBF | IC ADC 12BIT 125MSPS 3V 32-QFN |
| LTC2255CUH#TRPBF | IC ADC 14BIT 125MSPS 3V 32-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2242IUP-10-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:10-Bit, 250Msps ADC |
| LTC2242IUP-10-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:10-Bit, 250Msps ADC |
| LTC2242IUP-12 | 制造商:Linear Technology 功能描述:ADC Single Pipelined 250Msps 12-bit Parallel/LVDS 64-Pin QFN EP 制造商:Linear Technology 功能描述:MS-ADC/High Speed, 12-bit, 250Msps ADC |
| LTC2242IUP-12#PBF | 制造商:Linear Technology 功能描述:ADC Single Pipelined 250Msps 12-bit Parallel/LVDS 64-Pin QFN EP 制造商:Linear Technology 功能描述:Single ADC Pipelined 250Msps 12-bit Parallel/LVDS 64-Pin QFN EP 制造商:Linear Technology 功能描述:IC ADC 12BIT 250MSPS 64-QFN 制造商:Linear Technology 功能描述:A/D Converter (A-D) IC 制造商:Linear Technology 功能描述:IC, ADC, 12BIT, 250MSPS, QFN-64, Resolution (Bits):12bit, Sampling Rate:250MSPS, Supply Voltage Type:Single, Supply Voltage Min:2.375V, Supply Voltage Max:2.625V, Supply Current:285mA, Digital IC Case Style:QFN, No. of Pins:64 , RoHS Compliant: Yes 制造商:Linear Technology 功能描述:MS-ADC/High Speed, 12-bit, 250Msps ADC |
| LTC2242IUP-12#TRPBF | 制造商:Linear Technology 功能描述:ADC Single Pipelined 250Msps 12-bit Parallel/LVDS 64-Pin QFN EP T/R 制造商:Linear Technology 功能描述:IC ADC 12BIT 250MSPS 64-QFN |
发布紧急采购，3分钟左右您将得到回复。