- 您现在的位置：买卖IC网 > PDF目录10661 > LTC2256CUJ-14#PBF (Linear Technology)IC ADC 14BIT 25MSPS 1.8V 40-QFN PDF资料下载
参数资料
| 型号： | LTC2256CUJ-14#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/34页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 25MSPS 1.8V 40-QFN |
| 产品培训模块： | LTC2262 - Ultra Low Power High Speed ADCs |
| 标准包装： | 61 |
| 位数： | 14 |
| 采样率（每秒）： | 25M |
| 数据接口： | 并联，串行，SPI |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 40mW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN（6x6） |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分 |
| 配用： | DC718C-ND - DEMO QUIKEVAL-II DATA |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
LTC2258-14
LTC2257-14/LTC2256-14
22
225814fc
For more information www.linear.com/LTC2258-14
applicaTions inForMaTion
by mode control register A2 (serial programming mode),
or by CS (parallel programming mode).
Forapplicationswherethesamplerateneedstobechanged
quickly, the clock duty cycle stabilizer can be disabled. If
the duty cycle stabilizer is disabled, care should be taken
to make the sampling clock have a 50%(±5%) duty cycle.
The duty cycle stabilizer should not be used below 5Msps.
DIGITAL OUTPUTS
Digital Output Modes
TheLTC2258-14/LTC2257-14/LTC2256-14canoperatein
three digital output modes: full rate CMOS, double data
rate CMOS (to halve the number of output lines), or double
data rate LVDS (to reduce digital noise in the system). The
output mode is set by mode control register A3 (serial
programming mode), or by SCK (parallel programming
mode).NotethatdoubledatarateCMOScannotbeselected
in the parallel programming mode.
Full-Rate CMOS Mode
In full-rate CMOS mode the 14 digital outputs (D0-D13),
overflow (OF), and the data output clocks (CLKOUT+,
CLKOUT–) have CMOS output levels. The outputs are
powered by OVDD and OGND which are isolated from the
A/D core power and ground. OVDD can range from 1.1V
to 1.9V, allowing 1.2V through 1.8V CMOS logic outputs.
For good performance, the digital outputs should drive
minimal capacitive loads. If the load capacitance is larger
than 10pF a digital buffer should be used.
Double Data Rate CMOS Mode
In double data rate CMOS mode, two data bits are
multiplexed and output on each data pin. This reduces the
number of data lines by seven, simplifying board routing
and reducing the number of input pins needed to receive
the data. The 7 digital outputs (D0_1, D2_3, D4_5, D6_7,
D8_9, D10_11, D12_13), overflow (OF), and the data
output clocks (CLKOUT+, CLKOUT–) have CMOS output
levels. The outputs are powered by OVDDandOGNDwhich
are isolated from the A/D core power and ground. OVDD
can range from 1.1V to 1.9V, allowing 1.2V through 1.8V
CMOS logic outputs.
For good performance the digital outputs should drive
minimal capacitive loads. If the load capacitance is larger
than 10pF a digital buffer should be used.
Double Data Rate LVDS Mode
In double data rate LVDS mode, two data bits are
multiplexed and output on each differential output pair.
There are 7 LVDS output pairs (D0_1+/D0_1– through
D12_13+/D12_13–) for the digital output data. Overflow
(OF+/OF–)andthedataoutputclock(CLKOUT+/CLKOUT–)
each have an LVDS output pair.
By default the outputs are standard LVDS levels: 3.5mA
output current and a 1.25V output common mode volt-
age. An external 100 differential termination resistor
is required for each LVDS output pair. The termination
resistors should be located as close as possible to the
LVDS receiver.
The outputs are powered by OVDD and OGND which are
isolated from the A/D core power and ground. In LVDS
mode, OVDD must be 1.8V.
Programmable LVDS Output Current
In LVDS mode, the default output driver current is 3.5mA.
Thiscurrentcanbeadjustedbyseriallyprogrammingmode
control register A3. Available current levels are 1.75mA,
2.1mA, 2.5mA, 3mA, 3.5mA, 4mA and 4.5mA.
Optional LVDS Driver Internal Termination
In most cases using just an external 100 termination
resistor will give excellent LVDS signal integrity. In addi-
tion, an optional internal 100 termination resistor can
be enabled by serially programming mode control register
A3. The internal termination helps absorb any reflections
caused by imperfect termination at the receiver. When the
internal termination is enabled, the output driver current
is increased by 1.6x to maintain about the same output
voltage swing.
Overflow Bit
The overflow output bit (OF) outputs a logic high when
the analog input is either overranged or underranged. The
overflow bit has the same pipeline latency as the data bits.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B1X-IV-F4 | CONVERTER MOD DC/DC 5.2V 150W |
| MAX987EUK+TG103 | IC COMPARATOR R-R SOT23-5 |
| VI-B1X-IV-F3 | CONVERTER MOD DC/DC 5.2V 150W |
| AD7739BRUZ | IC ADC 24BIT 8-CH 24-TSSOP |
| MIC2550YML TR | IC USB TRANSCEIVER 16-MLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2256CUJ-14-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:14-Bit, 65/40/25Msps Ultralow Power 1.8V ADCs |
| LTC2256IUJ-12#PBF | 功能描述:IC ADC 12BIT 25MSPS 1.8V 40-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| LTC2256IUJ-12#TRPBF | 功能描述:IC ADC 12BIT 25MSPS 1.8V 40-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| LTC2256IUJ-12-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:12-Bit, 65/40/2 5Msps Ultralow Power 1.8V ADCs |
| LTC2256IUJ-12-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:12-Bit, 65/40/2 5Msps Ultralow Power 1.8V ADCs |
发布紧急采购，3分钟左右您将得到回复。