- 您现在的位置：买卖IC网 > PDF目录10661 > LTC2256CUJ-14#PBF (Linear Technology)IC ADC 14BIT 25MSPS 1.8V 40-QFN PDF资料下载
参数资料
| 型号： | LTC2256CUJ-14#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/34页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 25MSPS 1.8V 40-QFN |
| 产品培训模块： | LTC2262 - Ultra Low Power High Speed ADCs |
| 标准包装： | 61 |
| 位数： | 14 |
| 采样率（每秒）： | 25M |
| 数据接口： | 并联，串行，SPI |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 40mW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN（6x6） |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分 |
| 配用： | DC718C-ND - DEMO QUIKEVAL-II DATA |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
15
225814fc
LTC2258-14
LTC2257-14/LTC2256-14
For more information www.linear.com/LTC2258-14
pin FuncTions
PINS THAT ARE THE SAME FOR ALL DIGITAL OUTPUT
MODES
AIN+ (Pin 1): Positive Differential Analog Input.
AIN– (Pin 2): Negative Differential Analog Input.
GND (Pin 3): ADC Power Ground.
REFH (Pins 4, 5): ADC High Reference. Bypass to Pins
6, 7 with a 2.2F ceramic capacitor and to ground with a
0.1F ceramic capacitor.
REFL (Pins 6, 7): ADC Low Reference. Bypass to Pins
4, 5 with a 2.2F ceramic capacitor and to ground with a
0.1F ceramic capacitor.
PAR/SER (Pin 8): Programming Mode Selection Pin. Con-
nect to ground to enable the serial programming mode.
CS, SCK, SDI, SDO become a serial interface that control
the A/D operating modes. Connect to VDD to enable the
parallel programming mode where CS, SCK, SDI become
parallel logic inputs that control a reduced set of the A/D
operating modes. PAR/SER should be connected directly
to ground or the VDD of the part and not be driven by a
logic signal.
VDD (Pins 9, 10, 40): 1.8V Analog Power Supply. Bypass
to ground with 0.1F ceramic capacitors. Pins 9 and 10
can share a bypass capacitor.
ENC+ (Pin 11): Encode Input. Conversion starts on the
rising edge.
ENC– (Pin 12): Encode Complement Input. Conversion
starts on the falling edge.
CS (Pin 13): In serial programming mode, (PAR/SER =
0V), CS is the serial interface chip select input. When
CS is low, SCK is enabled for shifting data on SDI into
the mode control registers. In the parallel programming
mode (PAR/SER = VDD), CS controls the clock duty cycle
stabilizer. When CS is low, the clock duty cycle stabilizer is
turned off. When CS is high, the clock duty cycle stabilizer
is turned on. CS can be driven with 1.8V to 3.3V logic.
SCK (Pin 14): In serial programming mode, (PAR/SER
= 0V), SCK is the serial interface clock input. In the
parallel programming mode (PAR/SER = VDD), SCK
controls the digital output mode. When SCK is low,
the full-rate CMOS output mode is enabled. When SCK
is high, the double data rate LVDS output mode (with
3.5mA output current) is enabled. SCK can be driven
with 1.8V to 3.3V logic.
SDI (Pin 15): In serial programming mode, (PAR/SER =
0V), SDI is the serial interface data input. Data on SDI is
clocked into the mode control registers on the rising edge
of SCK. In the parallel programming mode (PAR/SER =
VDD), SDI can be used to power down the part. When SDI
is low, the part operates normally. When SDI is high, the
part enters sleep mode. SDI can be driven with 1.8V to
3.3V logic.
SDO (Pin 16): In serial programming mode, (PAR/SER
= 0V), SDO is the optional serial interface data output.
Data on SDO is read back from the mode control registers
and can be latched on the falling edge of SCK. SDO is an
open-drain NMOS output that requires an external 2k
pull-up resistor to 1.8V-3.3V. If read back from the mode
control registers is not needed, the pull-up resistor is not
necessary and SDO can be left unconnected. In the parallel
programming mode (PAR/SER = VDD), SDO is not used
and should not be connected.
OGND (Pin 25): Output Driver Ground.
OVDD (Pin 26): Output Driver Supply. Bypass to ground
with a 0.1F ceramic capacitor.
VCM (Pin 37): Common Mode Bias Output, Nominally
Equal to VDD/2. VCM should be used to bias the common
mode of the analog inputs. Bypass to ground with a 0.1F
ceramic capacitor.
VREF(Pin38):ReferenceVoltageOutput,Nominally1.25V.
Bypass to ground with a 1F ceramic capacitor.
SENSE(Pin39):ReferenceProgrammingPin.Connecting
SENSEtoVDDselectstheinternalreferenceanda±1Vinput
range. Connecting SENSE to ground selects the internal
reference and a ±0.5V input range. An external reference
between 0.625V and 1.3V applied to SENSE selects an
input range of ±0.8 VSENSE.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B1X-IV-F4 | CONVERTER MOD DC/DC 5.2V 150W |
| MAX987EUK+TG103 | IC COMPARATOR R-R SOT23-5 |
| VI-B1X-IV-F3 | CONVERTER MOD DC/DC 5.2V 150W |
| AD7739BRUZ | IC ADC 24BIT 8-CH 24-TSSOP |
| MIC2550YML TR | IC USB TRANSCEIVER 16-MLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2256CUJ-14-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:14-Bit, 65/40/25Msps Ultralow Power 1.8V ADCs |
| LTC2256IUJ-12#PBF | 功能描述:IC ADC 12BIT 25MSPS 1.8V 40-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| LTC2256IUJ-12#TRPBF | 功能描述:IC ADC 12BIT 25MSPS 1.8V 40-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| LTC2256IUJ-12-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:12-Bit, 65/40/2 5Msps Ultralow Power 1.8V ADCs |
| LTC2256IUJ-12-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:12-Bit, 65/40/2 5Msps Ultralow Power 1.8V ADCs |
发布紧急采购，3分钟左右您将得到回复。