- 您现在的位置：买卖IC网 > PDF目录10252 > LTC2449IUHF#PBF (Linear Technology)IC ADC 24BIT HI SPEED 38QFN PDF资料下载
参数资料
| 型号： | LTC2449IUHF#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 27/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT HI SPEED 38QFN |
| 标准包装： | 52 |
| 位数： | 24 |
| 采样率（每秒）： | 8k |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 40mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 管件 |
| 输入数目和类型： | 16 个单端，双极；8 个差分，双极 |
| 配用： | DC742A-ND - BOARD DELTA SIGMA ADC LTC2449 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页
LTC2444/LTC2445/
LTC2448/LTC2449
8
2444589fb
Initially, the LTC2444/LTC2445/LTC2448/LTC2449 per-
form a conversion. Once the conversion is complete, the
device enters the sleep state. While in this sleep state,
power consumption is reduced below 10
A. The part
remains in the sleep state as long as CS is HIGH. The
conversion result is held indefinitely in a static shift
register while the converter is in the sleep state.
Once CS is pulled LOW, the device begins outputting the
conversion result. There is no latency in the conversion
result while operating in the 1x mode. The data output cor-
responds to the conversion just performed. This result is
shifted out on the serial data out pin (SDO) under the con-
trol of the serial clock (SCK). Data is updated on the falling
edge of SCK allowing the user to reliably latch data on the
rising edge of SCK (see Figure 3). The data output state is
concluded once 32 bits are read out of the ADC or when CS
is brought HIGH. The device automatically initiates a new
conversion and the cycle repeats.
Through timing control of the CS, SCK and EXT pins, the
LTC2444/LTC2445/LTC2448/LTC2449 offer several flex-
ible modes of operation (internal or external SCK). These
various modes do not require programming configuration
registers; moreover, they do not disturb the cyclic opera-
tion described above. These modes of operation are
described in detail in the Serial Interface Timing Modes
section.
Ease of Use
The LTC2444/LTC2445/LTC2448/LTC2449 data output
has no latency, filter settling delay or redundant data
associated with the conversion cycle while operating in
the 1X mode. There is a one-to-one correspondence
between the conversion and the output data. Therefore,
multiplexing multiple analog voltages is easy. Speed/
resolution adjustments may be made seamlessly be-
tween two conversions without settling errors.
The LTC2444/LTC2445/LTC2448/LTC2449 perform off-
set and full-scale calibrations every conversion cycle. This
calibration is transparent to the user and has no effect on
the cyclic operation described above. The advantage of
continuous calibration is extreme stability of offset and
full-scale readings with respect to time, supply voltage
change and temperature drift.
APPLICATIO S I FOR ATIO
WU
U
Power-Up Sequence
The LTC2444/LTC2445/LTC2448/LTC2449 automatically
enter an internal reset state when the power supply
voltage VCC drops below approximately 2.2V. This fea-
ture guarantees the integrity of the conversion result and
of the serial interface mode selection.
When the VCC voltage rises above this critical threshold,
the converter creates an internal power-on-reset (POR)
signal with a duration of approximately 0.5ms. The POR
signal clears all internal registers. The conversion imme-
diately following a POR is performed on the input channel
IN+ = CH0, IN– = CH1 at an OSR = 256 in the 1X mode.
Following the POR signal, the LTC2444/LTC2445/LTC2448/
LTC2449 start a normal conversion cycle and follow the
succession of states described above. The first conver-
sion result following POR is accurate within the specifica-
tions of the device if the power supply voltage is restored
within the operating range (4.5V to 5.5V) before the end of
the POR time interval.
Reference Voltage Range
These converters accept a truly differential external refer-
ence voltage. The absolute/common mode voltage speci-
fication for the REF+ and REF– pins covers the entire range
from GND to VCC. For correct converter operation, the
REF+ pin must always be more positive than the REF– pin.
The LTC2444/LTC2445/LTC2448/LTC2449 can accept a
differential reference voltage from 0.1V to VCC. The con-
verter output noise is determined by the thermal noise of
the front-end circuits, and as such, its value in microvolts
is nearly constant with reference voltage. A decrease in
reference voltage will not significantly improve the
converter’s effective resolution. On the other hand, a
reduced reference voltage will improve the converter’s
overall INL performance.
Input Voltage Range
The analog input is truly differential with an absolute/
common mode range for the CH0-CH15 and COM input
pins extending from GND – 0.3V to VCC + 0.3V. Outside
these limits, the ESD protection devices begin to turn on
and the errors due to input leakage current increase
rapidly. Within these limits, the LTC2444/LTC2445/
相关PDF资料 |
PDF描述 |
|---|---|
| VE-26F-IU-S | CONVERTER MOD DC/DC 72V 200W |
| AD7829BRU | IC ADC 8BIT 8CH 2MSPS 28TSSOP |
| LTC2447IUHF#TRPBF | IC ADC 24BIT 8CH HI SPEED 38QFN |
| LTC1867CGN | IC ADC 16BIT 8CH 200KSPS 16SSOP |
| VE-22V-MX-F3 | CONVERTER MOD DC/DC 5.8V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2450CDC#PBF | 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 30sps 16-bit Serial 6-Pin DFN EP 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 0.03KSPS 16-Bit Serial 6-Pin DFN EP 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 0.03KSPS 16-Bit Serial 6-Pin DFN EP Bulk 制造商:Linear Technology 功能描述:ADC 16BIT 30SPS SPI DFN-6 制造商:Linear Technology 功能描述:ADC, 16BIT, 30SPS, SPI, DFN-6; Resolution (Bits):16bit; Sampling Rate:30SPS; Supply Voltage Type:Single; Supply Voltage Min:2.7V; Supply Voltage Max:5.5V; Supply Current:350A; Digital IC Case Style:DFN; No. of Pins:6 ;RoHS Compliant: Yes |
| LTC2450CDC#TRMPBF | 功能描述:IC ADC 16BIT DELTA SIG 6-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 位数:10 采样率（每秒）:357k 数据接口:DSP，MICROWIRE?，QSPI?，串行，SPI? 转换器数目:1 功率耗散（最大）:830µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:剪切带 (CT) 输入数目和类型:2 个单端，单极；2 个单端，双极；1 个差分，单极；1 个差分，双极 产品目录页面:1396 (CN2011-ZH PDF) 其它名称:MAX1395ETB+TCT |
| LTC2450CDC#TRPBF | 功能描述:IC ADC 16BIT DELTA SIG 6-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2450CDC-1#PBF | 制造商:Linear Technology 功能描述:EASY-TO-USE, ULTRA-TINY 16-BIT DELTA SEGMA ADC 制造商:Linear Technology 功能描述:Bulk 制造商:Linear Technology 功能描述:ADC 16BIT DEL SIG 60HZ 6DF 制造商:Linear Technology 功能描述:ADC, 16BIT, 60SPS, SPI, DFN-6; Resolution (Bits):16bit; Sampling Rate:60SPS; Supply Voltage Type:Single; Supply Voltage Min:2.7V; Supply Voltage Max:5.5V; Supply Current:350A; Digital IC Case Style:DFN; No. of Pins:6 ;RoHS Compliant: Yes |
| LTC2450CDC-1#TRMPBF | 功能描述:IC ADC 16BIT DELTA SIG 6-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
发布紧急采购，3分钟左右您将得到回复。