参数资料
| 型号： | LTC2605CGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 5/18页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT OCT I2C 16-SSOP |
| 标准包装： | 100 |
| 设置时间： | 10µs |
| 位数： | 16 |
| 数据接口： | I²C |
| 转换器数目： | 8 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 6mW |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
| 输出数目和类型： | 8 电压，单极 |
| 采样率（每秒）： | * |
| 配用： | DC935A-ND - BOARD DAC LTC2605 |
LTC2605/LTC2615/LTC2625
13
2605fa
OPERATION
The format of the three data bytes is shown in Figure 2.
The rst byte of the input word consists of the 4-bit com-
mand and 4-bit DAC address. The next two bytes consist
of the 16-bit data word. The 16-bit data word consists of
the 16-, 14- or 12-bit input code, MSB to LSB, followed by
0, 2 or 4 don’t care bits (LTC2605, LTC2615 and LTC2625
respectively). A typical I2C write transaction is shown in
Figure 3.
The command (C3-C0) and address (A3-A0) assignments
are shown in Table 1. The rst four commands in the table
consist of write and update operations. A write operation
loads the 16-bit data word from the 32-bit shift register
into the input register of the selected DAC, n. An update
operation copies the data word from the input register to
the DAC register. Once copied into the DAC register, the
data word becomes the active 16-, 14- or 12-bit input
code, and is converted to an analog voltage at the DAC
output. The update operation also powers up the selected
DAC if it had been in power-down mode. The data path
and registers are shown in the Block Diagram.
Power-Down Mode
For power-constrained applications, power-down mode
can be used to reduce the supply current whenever less
than eight outputs are needed. When in power down, the
buffer ampliers and reference inputs are disabled and
draw essentially zero current. The DAC outputs are put into
a high impedance state, and the output pins are passively
pulled to ground through individual 90k resistors. When
all eight DACs are powered down, the bias generation
circuit is also disabled. Input and DAC registers are not
disturbed during power down.
Any channel or combination of channels can be put into
power-down mode by using command 0100b in combi-
nation with the appropriate DAC address, (n). The 16-bit
data word is ignored. The supply and reference currents
are reduced by approximately 1/8 for each DAC powered
down; the effective resistance at REF (Pin 6) rises accord-
ingly, becoming a high impedance input (typically >1GΩ)
when all eight DACs are powered down.
Normal operation can be resumed by executing any com-
mand which includes a DAC update, as shown in Table 1.
The selected DAC is powered up as its voltage output is
updated.
There is an initial delay as the DAC powers up before it
begins its usual settling behavior. If less than eight DACs
are in a powered-down state prior to the updated com-
mand, the power-up delay is 5μs. If, on the other hand,
all eight DACs are powered down, then the bias genera-
tion circuit is also disabled and must be restarted. In this
case, the power-up delay is greater: 12μs for VCC = 5V,
30μs for VCC = 3V.
S
INPUT WORD
WRITE WORD PROTOCOL FOR LTC2605/LTC2615/LTC2625
INPUT WORD (LTC2605)
SLAVE ADDRESS
W
A
1ST DATA BYTE
2ND DATA BYTE
A
3RD DATA BYTE
AP
2605 F02
1ST DATA BYTE
2ND DATA BYTE
3RD DATA BYTE
1ST DATA BYTE
2ND DATA BYTE
3RD DATA BYTE
1ST DATA BYTE
2ND DATA BYTE
3RD DATA BYTE
C3
C2
C1
C0
A3
A2
A1
A0
D13
D14
D15
D12 D11 D10 D9
D8
D7 D6
D5
D4
D3
D2
D1 D0
INPUT WORD (LTC2615)
C3
C2
C1
C0
A3
A2
A1
A0
D11
D12
D13
D10 D9
D8
D7
D6
D5 D4
D3
D2
D1
D0
X
INPUT WORD (LTC2625)
C3
C2
C1
C0
A3
A2
A1
A0
D9
D10
D11
D8
D7
D6
D5
D4
D3 D2
D1
D0
X
Figure 2
相关PDF资料 |
PDF描述 |
|---|---|
| AD7564ARS-BREEL | IC DAC 12BIT QUAD 3.3V LP 28SSOP |
| SY88923AVKC TR | IC AMP POST 5V/3.3V 10-MSOP |
| VE-25P-IV-F2 | CONVERTER MOD DC/DC 13.8V 150W |
| SY88923AVKC | IC AMP POST 5V/3.3V 10-MSOP |
| VE-25N-IV-F1 | CONVERTER MOD DC/DC 18.5V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2605IGN#PBF | 功能描述:IC DAC 16BIT OCT I2C 16-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| LTC2605IGN#TRPBF | 功能描述:IC DAC 16BIT OCT I2C 16-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| LTC2605IGN-1#PBF | 功能描述:IC DAC 16BIT OCT I2C 16-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 设置时间:4µs 位数:12 数据接口:串行 转换器数目:2 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-uMAX 包装:管件 输出数目和类型:2 电压，单极 采样率（每秒）:* 产品目录页面:1398 (CN2011-ZH PDF) |
| LTC2605IGN-1#TRPBF | 功能描述:IC DAC 16BIT OCT I2C 16-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| LTC2606CDD#PBF | 功能描述:IC DAC 16BIT I2C V-OUT 10-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 设置时间:4µs 位数:12 数据接口:串行 转换器数目:2 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-uMAX 包装:管件 输出数目和类型:2 电压，单极 采样率（每秒）:* 产品目录页面:1398 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。