- 您现在的位置：买卖IC网 > PDF目录8607 > LTC2751AIUHF-16#TRPBF (Linear Technology)IC DAC 16BIT CUR OUT 38-QFN PDF资料下载
参数资料
| 型号： | LTC2751AIUHF-16#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/22页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT CUR OUT 38-QFN |
| 产品培训模块： | LTC275x 18-Bit DAC |
| 标准包装： | 2,500 |
| 系列： | SoftSpan™ |
| 设置时间： | 2µs |
| 位数： | 16 |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 2 电流，单极；2 电流，双极 |
| 采样率（每秒）： | * |
| 配用： | DC1110A-ND - BOARD DAC LTC2751-16 |
LTC2751
17
2751fa
applicaTions inForMaTion
Op amp offset will contribute mostly to output offset and
gain error and has minimal effect on INL and DNL. For
the LTC2751-16, a 250V op amp offset will cause about
0.8LSB INL degradation and 0.2LSB DNL degradation
with a 5V reference. For the LTC2751 programmed in 5V
unipolar mode, the same 250V op amp offset will cause
a 3.3LSB zero-scale error and a 3.3LSB gain error.
While not directly addressed by the simple equations in
Tables 3 and 4, temperature effects can be handled just
as easily for unipolar and bipolar applications. First, con-
sult an op amp’s data sheet to find the worst-case VOS
and IB over temperature. Then, plug these numbers in
the VOS and IB equations from Table 4 and calculate the
temperature-induced effects.
For applications where fast settling time is important,
Application Note 74, “Component and Measurement
Advances Ensure 16-Bit DAC Settling Time,” offers a
thorough discussion of 16-bit DAC settling time and op
amp selection.
Precision Voltage Reference Considerations
Much in the same way selecting an operational amplifier
for use with the LTC2751 is critical to the performance of
the system, selecting a precision voltage reference also
requiresduediligence.TheoutputvoltageoftheLTC2751is
directlyaffectedbythevoltagereference;thus,anyvoltage
reference error will appear as a DAC output voltage error.
There are three primary error sources to consider when
selecting a precision voltage reference for 16-bit appli-
cations: output voltage initial tolerance, output voltage
temperature coefficient and output voltage noise.
Initial reference output voltage tolerance, if uncorrected,
generates a full-scale error term. Choosing a reference
with low output voltage initial tolerance, like the LT1236
(±0.05%), minimizes the gain error caused by the refer-
ence; however, a calibration sequence that corrects for
system zero- and full-scale error is always recommended.
Areference’soutputvoltagetemperaturecoefficientaffects
not only the full-scale error, but can also affect the circuit’s
INL and DNL performance. If a reference is chosen with
a loose output voltage temperature coefficient, then the
DAC output voltage along its transfer characteristic will
be very dependent on ambient conditions. Minimizing
the error due to reference temperature coefficient can be
achieved by choosing a precision reference with a low
output voltage temperature coefficient and/or tightly con-
trolling the ambient temperature of the circuit to minimize
temperature gradients.
As precision DAC applications move to 16-bit and higher
performance, reference output voltage noise may contrib-
ute a dominant share of the system’s noise floor. This in
turn can degrade system dynamic range and signal-to-
noise ratio. Care should be exercised in selecting a voltage
reference with as low an output noise voltage as practi-
cal for the system resolution desired. Precision voltage
references, like the LT1236, produce low output noise in
the 0.1Hz to 10Hz region, well below the 16-bit LSB level
in 5V or 10V full-scale systems. However, as the circuit
bandwidths increase, filtering the output of the reference
may be required to minimize output noise.
Table 6. Partial List of LTC Precision References Recommended
for Use with the LTC2751 with Relevant Specifications
REFERENCE
INITIAL
TOLERANCE
TEMPERATURE
DRIFT
0.1Hz to 10Hz
NOISE
LT1019A-5,
LT1019A-10
±0.05%
5ppm/°C
12VP-P
LT1236A-5,
LT1236A-10
±0.05%
5ppm/°C
3VP-P
LT1460A-5,
LT1460A-10
±0.075%
10ppm/°C
20VP-P
LT1790A-2.5
±0.05%
10ppm/°C
12VP-P
Grounding
As with any high resolution converter, clean grounding is
important. A low impedance analog ground plane and star
grounding techniques should be used. IOUT2 must be tied
to the star ground with as low a resistance as possible.
When it is not possible to locate star ground close to
IOUT2, a low resistance trace should be used to route this
pin to star ground. This minimizes the voltage drop from
this pin to ground caused by the code dependent current
flowing to ground. When the resistance of this circuit
board trace becomes greater than 1
W, a force/sense am-
plified configuration should be used to drive this pin (see
Figure 2). This preserves the excellent accuracy (1LSB
INL and DNL) of the LTC2751-16.
相关PDF资料 |
PDF描述 |
|---|---|
| AD8332ARUZ-R7 | IC AMP VAR GAIN 2CHAN 28TSSOP |
| VI-24J-IV-F3 | CONVERTER MOD DC/DC 36V 150W |
| AD8332ARUZ-RL | IC AMP VAR GAIN 2CHAN 28TSSOP |
| AD5328ARU | IC DAC 12BIT OCTAL W/BUF 16TSSOP |
| AD8332ACPZ-RL | IC AMP VAR GAIN 2CHAN 32LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2751BCUHF-16#PBF | 功能描述:IC DAC 16BIT CUR OUT 38-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:SoftSpan™ 标准包装:47 系列:- 设置时间:2µs 位数:14 数据接口:并联 转换器数目:1 电压电源:单电源 功率耗散（最大）:55µW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:管件 输出数目和类型:1 电流，单极；1 电流，双极 采样率（每秒）:* |
| LTC2751BCUHF-16#TRPBF | 功能描述:IC DAC 16BIT CUR OUT 38-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:SoftSpan™ 标准包装:47 系列:- 设置时间:2µs 位数:14 数据接口:并联 转换器数目:1 电压电源:单电源 功率耗散（最大）:55µW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:管件 输出数目和类型:1 电流，单极；1 电流，双极 采样率（每秒）:* |
| LTC2751BIUHF-16#PBF | 功能描述:IC DAC 16BIT CUR OUT 38-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:SoftSpan™ 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| LTC2751BIUHF-16#TRPBF | 功能描述:IC DAC 16BIT CUR OUT 38-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:SoftSpan™ 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| LTC2751CUHF-12#PBF | 功能描述:IC DAC 12BIT CUR OUT 38-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:SoftSpan™ 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?，串行，SPI? 转换器数目:8 电压电源:单电源 功率耗散（最大）:2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-DFN-EP（4x3） 包装:管件 输出数目和类型:8 电压，单极 采样率（每秒）:* |
发布紧急采购，3分钟左右您将得到回复。