- 您现在的位置：买卖IC网 > PDF目录1829 > LTC3403EDD#TRPBF (Linear Technology)IC REG BUCK SYNC ADJ 0.6A 8DFN PDF资料下载
参数资料
| 型号： | LTC3403EDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 0.6A 8DFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.3 V ~ 3.5 V |
| 输入电压： | 2.5 V ~ 5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 1.5MHz |
| 电流 - 输出： | 600mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-DFN-EP（3x3） |
LTC3403
OPERATIO
1200
1000
(Refer to Functional Diagram)
Slope Compensation and Inductor Peak Current
Slope compensation provides stability in constant fre-
800
600
V OUT = 1.8V
V OUT = 1.5V
V OUT = 2.5V
quency architectures by preventing subharmonic oscilla-
tions at high duty cycles. It is accomplished internally by
adding a compensating ramp to the inductor current
signal at duty cycles in excess of 40%. Normally, this
400
200
results in a reduction of maximum inductor peak current
for duty cycles > 40%. However, the LTC3403 uses a
patent-pending scheme that counteracts this compensat-
0
2.5
3.0
3.5 4.0 4.5
5.0
5.5
ing ramp, which allows the maximum inductor peak
SUPPLY VOLTAGE (V)
3403 F02
Figure 2. Maximum Output Current vs Input Voltage
APPLICATIO S I FOR ATIO
The basic LTC3403 application circuit is shown in Fig-
ure 1. External component selection is driven by the load
requirement and begins with the selection of L followed by
C IN and C OUT .
Inductor Selection
For most applications, the value of the inductor will fall in
the range of 1 μ H to 4.7 μ H. Its value is chosen based on the
desired ripple current. Large value inductors lower ripple
current and small value inductors result in higher ripple
currents. As Equation 1 shows, a greater difference be-
tween V IN and V OUT produces a larger ripple current.
Where these voltages are subject to change, the highest
V IN and lowest V OUT will determine the maximum ripple
current. A reasonable starting point for setting ripple
current is I L = 240mA (40% of the maximum load, 600mA).
current to remain unaffected throughout all duty cycles.
The DC current rating of the inductor should be at least
equal to the maximum load current plus half the ripple
current to prevent core saturation. Thus, a 720mA rated
inductor should be enough for most applications (600mA
+ 120mA). For better efficiency, choose a low DC-resis-
tance inductor.
The inductor value also has an effect on Burst Mode
operation. The transition to low current operation begins
when the inductor current peaks fall to approximately
200mA. Lower inductor values (higher I L ) will cause this
to occur at lower load currents, which can cause a dip in
efficiency in the upper range of low current operation. In
Burst Mode operation, lower inductance values will cause
the burst frequency to increase.
Inductor Core Selection
V OUT ? 1 – OUT ?
? I L =
1
( f )( L )
? V ?
? V IN ?
(1)
Different core materials and shapes will change the size/
current and price/current relationship of an inductor.
Toroid or shielded pot cores in ferrite or permalloy mate-
At output voltages below 0.6V, the switching frequency
decreases linearly to a minimum of approximately 700kHz.
This places the maximum ripple current (in forced con-
tinuous mode) at the highest input voltage and the lowest
output voltage. In practice, the resulting ouput ripple
voltage is 10mV to 15mV using the components specified
in Figure 1.
rials are small and don’t radiate much energy but generally
cost more than powdered iron core inductors with similar
electrical characteristics. The choice of which style induc-
tor to use often depends more on the price versus size
requirements and any radiated field/EMI requirements
than on what the LTC3403 requires to operate. Table 1
shows some typical surface mount inductors that work
well in LTC3403 applications.
3403f
9
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3404MPMS8#PBF | IC REG BUCK SYNC ADJ 0.6A 8MSOP |
| LTC3405ES6#TRPBF | IC REG BUCK SYNC ADJ .3A SOT23-6 |
| LTC3406BES5-1.2#TRPBF | IC REG BUCK SYNC 1.2V TSOT23-5 |
| LTC3406ES5-1.8#TRPBF | IC REG BUCK SYNC 1.8V TSOT23-5 |
| LTC3407EDD#TRPBF | IC REG BUCK SYNC ADJ 1A DL 10DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3404 | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.4MHz High Efficiency Monolithic Synchronous Step-Down Regulator |
| LTC3404EMS8 | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3404EMS8#PBF | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3404EMS8#TR | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3404EMS8#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。