- 您现在的位置：买卖IC网 > PDF目录69007 > LTC3406AES5#TRM (LINEAR TECHNOLOGY CORP) 1.3 A SWITCHING REGULATOR, 1800 kHz SWITCHING FREQ-MAX, PDSO5 PDF资料下载
参数资料
| 型号： | LTC3406AES5#TRM |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 1.3 A SWITCHING REGULATOR, 1800 kHz SWITCHING FREQ-MAX, PDSO5 |
| 封装： | 1 MM HEIGHT, LEAD FREE, PLASTIC, MO-193, TSOT-23, 5 PIN |
| 文件页数： | 14/16页 |
| 文件大小： | 265K |
| 代理商： | LTC3406AES5#TRM |
LTC3406A
7
3406af
Main Control Loop
The LTC3406A uses a constant frequency, current mode
step-down architecture. Both the main (P-channel
MOSFET) and synchronous (N-channel MOSFET) switches
are internal. During normal operation, the internal top power
MOSFET is turned on each cycle when the oscillator sets
the RS latch, and turned off when the current comparator,
ICOMP, resets the RS latch. The peak inductor current at
which ICOMP resets the RS latch, is controlled by the output
of error amplier EA. When the load current increases,
it causes a slight decrease in the feedback voltage, FB,
relative to the 0.6V reference, which in turn, causes the
EA amplier’s output voltage to increase until the average
inductor current matches the new load current. While the
top MOSFET is off, the bottom MOSFET is turned on until
either the inductor current starts to reverse, as indicated
by the current reversal comparator IRCMP, or the beginning
of the next clock cycle.
The main control loop is shut down by grounding RUN,
resetting the internal soft-start. Re-enabling the main
control loop by pulling RUN high activates the internal
soft-start, which slowly ramps the output voltage over
approximately 0.9ms until it reaches regulation.
Burst Mode Operation
The LTC3406A is capable of Burst Mode operation in which
the internal power MOSFETs operate intermittently based
on load demand.
In Burst Mode operation, the peak current of the inductor
is set to approximately 100mA regardless of the output
load. Each burst event can last from a few cycles at light
loads to almost continuously cycling with short sleep
intervals at moderate loads. In between these burst events,
the power MOSFETs and any unneeded circuitry are turned
off, reducing the quiescent current to 20μA. In this sleep
state, the load current is being supplied solely from the
output capacitor. As the output voltage droops, the EA
amplier’s output rises above the sleep threshold signaling
the BURST comparator to trip and turn the top MOSFET
on. This process repeats at a rate that is dependent on
the load demand.
Dropout Operation
As the input supply voltage decreases to a value approach-
ing the output voltage, the duty cycle increases toward the
maximum on-time. Further reduction of the supply voltage
forces the main switch to remain on for more than one cycle
until it reaches 100% duty cycle. The output voltage will
then be determined by the input voltage minus the voltage
drop across the P-channel MOSFET and the inductor.
An important detail to remember is that at low input supply
voltages, the RDS(ON) of the P-channel switch increases
(see Typical Performance Characteristics). Therefore,
the user should calculate the power dissipation when
the LTC3406A is used at 100% duty cycle with low input
voltage (See Thermal Considerations in the Applications
Information section).
Slope Compensation and Inductor Peak Current
Slope compensation provides stability in constant fre-
quency architectures by preventing subharmonic oscilla-
tions at high duty cycles. It is accomplished internally by
adding a compensating ramp to the inductor current signal
at duty cycles in excess of 40%. Normally, this results in
a reduction of maximum inductor peak current for duty
cycles > 40%. However, the LTC3406A uses a patented
scheme that counteracts this compensating ramp, which
allows the maximum inductor peak current to remain
unaffected throughout all duty cycles.
OPERATION (Refer to Functional Diagram)
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3406AES5#TR | 1.3 A SWITCHING REGULATOR, 1800 kHz SWITCHING FREQ-MAX, PDSO5 |
| LTC3406AIS5#PBF | 1.3 A SWITCHING REGULATOR, 1800 kHz SWITCHING FREQ-MAX, PDSO5 |
| LTC3406AES5#PBF | 1.3 A SWITCHING REGULATOR, 1800 kHz SWITCHING FREQ-MAX, PDSO5 |
| LTC3406BES5#PBF | 1.25 A SWITCHING REGULATOR, 1800 kHz SWITCHING FREQ-MAX, PDSO5 |
| LTC3406BES5-1.8#PBF | 1.25 A SWITCHING REGULATOR, 1800 kHz SWITCHING FREQ-MAX, PDSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3406AES5-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.5MHz, 600mA Synchronous Step-Down Regulator in ThinSOT |
| LTC3406AIS5#PBF | 制造商:Linear Technology 功能描述:DP-SWREG/Monolithic, Cut Tape 1.5MHz, 600mA Synch Step Down Regulator |
| LTC3406AIS5#TRMPBF | 功能描述:IC REG BUCK SYNC ADJ TSOT23-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3406AIS5#TRPBF | 功能描述:IC REG BUCK SYNC ADJ TSOT23-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3406AIS5-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.5MHz, 600mA Synchronous Step-Down Regulator in ThinSOT |
发布紧急采购，3分钟左右您将得到回复。