- 您现在的位置：买卖IC网 > PDF目录1829 > LTC3415EUHF#TRPBF (Linear Technology)IC REG BUCK SYNC ADJ 7A 38QFN PDF资料下载
参数资料
| 型号： | LTC3415EUHF#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 7A 38QFN |
| 标准包装： | 2,500 |
| 系列： | PolyPhase® |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.7 V ~ 5.5 V |
| 输入电压： | 2.5 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 1.5MHz |
| 电流 - 输出： | 7A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 38-QFN（5x7） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC3415
OPERATION
noise vs free-running constant frequency operation. Spread
spectrum operation is disabled if CLKIN is tied to ground
frequency applications may approach this minimum on-
time limit and care should be taken to ensure that:
or if it’s driven by an external frequency synchronization
signal.
Dropout Operation
t ON(MIN) <
V OUT
(f ? V IN )
When the input supply voltage decreases toward the output
voltage, the duty cycle will increase toward the maximum
on-time. Further reduction of the supply voltage forces the
P-channel power MOSFET to remain on for more than one
cycle until it reaches 100% duty cycle. The output voltage
will then be determined by the input voltage minus the
voltage drop across the P-channel power MOSFET and
the inductor.
Slope Compensation and Inductor Peak Current
Slope compensation provides stability by preventing sub-
harmonic oscillations. It works by internally adding a ramp
to the inductor current signal at duty cycles in excess of
30%. This causes the internal current comparator to trip
earlier. The I TH clamp is also reached earlier than condi-
tions in which the duty cycle is below 30%. As a result,
the maximum inductor peak current is lower for higher
duty cycle operations.
To compensate for this loss in maximum inductor peak
current during high duty cycles, the LTC3415 uses a pat-
ented scheme that raises the I TH clamp level (proportional
to the amount of slope compensation) when the duty cycle
is greater than 30%.
Minimum On-Time Considerations
Minimum on-time, t ON(MIN) , is the smallest amount
of time that the LTC3415 is capable of turning the top
P-channel power MOSFET on and off again. It is determined
by the internal timing delays. The minimum on-time for
the LTC3415 is about 100ns. Low duty cycle and high
If the duty cycle falls below what can be accommodated
by the minimum on-time, the LTC3415 will begin to skip
cycles. The output voltage will continue to be regulated,
but the ripple current and ripple voltage will increase.
If an application can operate close to the minimum on-time
limit, an inductor must be chosen that has low enough
inductance to provide suf?cient ripple amplitude to meet
the minimum on-time requirement. As a general rule, keep
the inductor ripple current equal or greater than 30% of
the I OUT(MAX) at V IN(MAX) .
Output Margining
For a convenient system stress test on the LTC3415’s out-
put, the user can program the LTC3415’s output to ±5%,
±10% or ±15% of its normal operational voltage.
The MGN pin, when connected to a voltage between 0.5V
and SV IN – 0.SV allows normal operation. When the MGN
pin is low, it forces negative margining, in which the output
voltage is below the regulation point. When MGN is high, the
output voltage is forced to above the regulation point. The
amount of output voltage margining is determined by the
BSEL pin. When BSEL is low, it’s 5%. When BSEL is high,
it’s 10%. When BSEL is V IN /2, it’s 15%. When margining
is active, the internal output overvoltage and undervoltage
comparators are disabled and PGOOD remains high.
Output Power-Good
When the LTC3415’s output voltage is within a ±10%
window of the regulation point, which is re?ected back
as a V FB voltage in the range of 0.54V to 0.66V, the output
voltage is good and the PGOOD pin is pulled high with
the external resistor.
3415fa
14
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3416EFE#TRPBF | IC REG BUCK SYNC ADJ 4A 20TSSOP |
| LTC3417AIFE-1#TRPBF | IC REG BUCK SYNC ADJ DL 20TSSOP |
| LTC3417AIFE-2#TRPBF | IC REG BUCK SYNC ADJ DL 20TSSOP |
| LTC3417EDHC#PBF | IC REG BUCK SYNC ADJ DL 16DFN |
| LTC3418EUHF#TRPBF | IC REG BUCK SYNC ADJ 8A 38QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3416 | 制造商:LINEAR 制造商全称:LINEAR 功能描述:20V, 5A Synchronous Step-Down Regulator |
| LTC3416EFE | 功能描述:IC REG BUCK SYNC ADJ 4A 20TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3416EFE#PBF | 功能描述:IC REG BUCK SYNC ADJ 4A 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3416EFE#TR | 功能描述:IC REG BUCK SYNC ADJ 4A 20TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3416EFE#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 4A 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。